Transmission Planetary - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 176-6536     | 顶出螺栓     | 2     |
开始:
- 拆下后车桥油冷却器。
Show/hide table
高温机油或高温部件可能会导致人身伤害。 在工作温度下,机油温度高,压力高。 热油能造成烫伤。 只能在发动机停机且加注口盖充分冷却到可以徒手触及时再卸下加注口盖。 不让高温油或部件与皮肤接触。 |
Show/hide table
突然释放高压机油可能会导致人身伤害。 一定要关闭发动机至少五分钟,保证蓄能器压力为零。 蓄能器充满干氮气。不要松开蓄能器顶部的阀或卸下盖。 |
- 安装卡车车斗固定缆绳。 请参阅操作和保养手册, "卡车车斗固定缆绳 - 拆卸和安装"。
- 将液压油箱中的油排入合适的容器以便保存或废弃这些油。 请参阅操作和保养手册, "液压油箱 - 更换 - 举倾和制动系统"。
- 将变速箱中的油排入适当的容器中以便保存或处理。 参阅操作和保养手册, "变矩器和变速箱油 - 更换"。
- 拆下后驱动轴护罩 (1) 。
Show/hide table
图 1 | g02091121 |
- 在传动轴 (2) 下方安装适当的垫块。 传动轴 (2) 的重量约为 295 kg (650 lb)。 拆下螺栓 (3 ) 。 使用合适的撬杆缩回传动轴 (2) 。
Show/hide table
图 2 | g02092037 |
- 断开软管组件 (4) 。 拆下卡箍 (5) 。 断开管组件 (6) 。 断开线束组件 (7) 。 拆下卡箍 (8) 。 断开线束组件 (9) 。
Show/hide table
图 3 | g02092073 |
- 拆下卡箍 (10) 。 断开软管组件 (11) 。 断开软管 (12) 。
Show/hide table
图 4 | g02092115 |
- 断开线束组件 (13) 。
Show/hide table
图 5 | g02092256 |
- 断开软管组件 (14) 。 断开软管组件 (15) 。 断开线束组件 (16) 。
Show/hide table
图 6 | g02092214 |
- 断开线束组件 (17) 。 断开支架 (18) 。 拆下连接硬件并将线束组件 (19) 放到一边。
Show/hide table
图 7 | g02092394 |
- 断开软管组件 (20) 。
Show/hide table
图 8 | g02092473 |
- 断开软管组件 (21) 。
Show/hide table
图 9 | g02093861 |
- 断开软管组件 (22) 。 拆卸管组件 (23) 。
Show/hide table
图 10 | g02092553 |
- 将适当的起吊设备连接到变速箱 (24) 上。 变速箱 (24) 的重量约为 6260 kg (13800 lb)。 拆下螺栓 (25) 。 将工具 (A) 用作顶推螺栓以将变速箱 (24) 从后桥壳体上分离。
注: 可能会损坏输出轴花键。 确保输出轴脱离差速器。 小心地慢慢拆下变速箱。
Show/hide table
图 11 | g02092915 |
传动轴端部 |
Show/hide table
图 12 | g02092733 |
中位 |
Show/hide table
图 13 | g02093154 |
后桥端部 |
- 拆下变速箱 (24) 。
- 拆下 O 型密封圈 (26) 。
Show/hide table
图 14 | g02093204 |
安装步骤
- 按相反顺序安装变速箱 (24) 。
Caterpillar Information System:
797F Off-Highway Truck Power Train Differential and Bevel Gear - Install
797F Off-Highway Truck Power Train Differential and Bevel Gear - Remove
TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Warm-up
797 Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Assemble
797 Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Disassemble
C27 and C32 Engines for Caterpillar Built Machines Programmable Parameters
3500B Engines for Caterpillar Built Power Modules Disconnect Switch
C13, C15, and C18 Tier 4 Interim Engines Diesel Particulate Filter Has High Inlet Pressure
TH31-E61 and TH35-E81 Petroleum Transmissions Component Location
797F Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Remove and Install
C27 Generator Set Engines Connecting Rod
797F Off-Highway Truck Power Train Final Drive - Remove and Install - Horizontal
TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Cooling System
TH31-E61 and TH35-E81 Petroleum Transmissions Magnetic Screen (Transmission) - Clean - Drop Box
C13, C15, and C18 Tier 4 Interim Engines Sensor Signal (Analog, Active) - Test
Reuse and Salvage for 3500, 3600 & C175 Engine Oil Pans {1302} Reuse and Salvage for 3500, 3600 & C175 Engine Oil Pans {1302}
3516C Locomotive Engine and Generator Set Engine Oil and Filter - Change
C27 Generator Set Engines Turbocharger
2010/02/03 New Cylinder Packs or Piston Rings Are Available For Certain C13 Industrial Engines {1225}
2010/02/10 A New Alternator Is Used on Some Commercial Engines {1405}
3516C Locomotive Engine and Generator Set Plate Locations and Film Locations
C13, C15, and C18 Tier 4 Interim Engines Sensor Calibration Required - Test
C13, C15, and C18 Tier 4 Interim Engines Data Link Configuration Status - Test
C9.3 Engines for Caterpillar Built Machines Fuel Rail Pressure Is Low While Cranking