Differential and Bevel Gear - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 160-1831     | 起吊接头总成     | 1     |
- 检查所有的管和管组件是否有裂缝或过度磨损。 将盖 (10) 和磁铁安装到后桥壳体组件的各侧。
注: 必须安装盖 (10) 和磁铁,以便尺寸 (X) 为 162 ± 20 mm (6.4 ± 0.8 in) 和尺寸 (Y) 为 163 ± 10 mm (6.4 ± 0.4 in)。
Show/hide table
图 1 | g02089025 |
Show/hide table
图 2 | g00685342 |
- 安装 O 形密封圈 (9) 。
Show/hide table
图 3 | g02089020 |
- 安装 O 形密封圈 (8) 。
Show/hide table
图 4 | g02089017 |
- 使用工具 (A) 和适当的升降车以便安装差速器和伞齿轮 (5) 。 差速器和伞齿轮 (5) 的重量约为 3356 kg (7400 lb)。
Show/hide table
图 5 | g02089000 |
- 检查各螺栓 (4) 是否拉伸。 如果螺栓拉伸明显,建议使用新螺栓 (4) 。
Show/hide table
图 6 | g02088933 |
- 安装两个新的螺栓 (4) 以便保持住差速器和伞齿轮 (5) 。 拆下工具 (A) 。
- 安装将差速器和伞齿轮 (5) 固定到后桥壳体组件上的其余新螺栓 (4) 。
Show/hide table
图 7 | g02089035 |
- 将相互之间成 90 度分离的四个螺栓 (4) 拧紧至扭矩 800 ± 100 N·m (590 ± 74 lb ft)。
- 将其余螺栓 (4) 相继拧紧至扭矩为 800 ± 100 N·m (590 ± 74 lb ft)。
- 将螺栓 (5) 相继再拧紧 90 度。
- 安装滤网组件和滤网盖 (7) 。 安装螺栓 (6) 。
- 将护罩 (3) 放置到位并安装螺栓 (2) 。
Show/hide table
图 8 | g02088913 |
- 连接线束组件 (1) 并安装连接硬件。
Show/hide table
图 9 | g02088906 |
- 为差速器和终传动加油。 请参阅操作和保养手册, "差速器和终传动油和滤网 - 更换/清洁"。
End By: 安装半轴。
Caterpillar Information System:
797F Off-Highway Truck Power Train Differential and Bevel Gear - Remove
TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Warm-up
797 Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Assemble
797 Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Disassemble
C27 and C32 Engines for Caterpillar Built Machines Programmable Parameters
3500B Engines for Caterpillar Built Power Modules Disconnect Switch
C13, C15, and C18 Tier 4 Interim Engines Diesel Particulate Filter Has High Inlet Pressure
TH31-E61 and TH35-E81 Petroleum Transmissions Component Location
797F Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Remove and Install
C27 Generator Set Engines Connecting Rod
797F Off-Highway Truck Power Train Final Drive - Remove and Install - Horizontal
C15 and C18 Industrial Engines Electronic Unit Injector
797F Off-Highway Truck Power Train Transmission Planetary - Remove and Install
TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Cooling System
TH31-E61 and TH35-E81 Petroleum Transmissions Magnetic Screen (Transmission) - Clean - Drop Box
C13, C15, and C18 Tier 4 Interim Engines Sensor Signal (Analog, Active) - Test
Reuse and Salvage for 3500, 3600 & C175 Engine Oil Pans {1302} Reuse and Salvage for 3500, 3600 & C175 Engine Oil Pans {1302}
3516C Locomotive Engine and Generator Set Engine Oil and Filter - Change
C27 Generator Set Engines Turbocharger
2010/02/03 New Cylinder Packs or Piston Rings Are Available For Certain C13 Industrial Engines {1225}
2010/02/10 A New Alternator Is Used on Some Commercial Engines {1405}
3516C Locomotive Engine and Generator Set Plate Locations and Film Locations
C13, C15, and C18 Tier 4 Interim Engines Sensor Calibration Required - Test
C13, C15, and C18 Tier 4 Interim Engines Data Link Configuration Status - Test