Flywheel - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | FT-0120     | 提升支架     | 1     |
B     | -     | 导向螺柱 5/8 - 18 x 6 in     |
2     |
- 转动飞轮 (1) 直到螺纹孔 (2) 位于顶部。
Show/hide table
图 1 | g01951604 |
- 拆下上面的五个螺栓 (3) 。
- 将工具 (B) 安装在曲轴中。
Show/hide table
图 2 | g01951606 |
- 将工具 (A) 和适当的提升设备连接到飞轮 (1) 上。 飞轮 (1) 的重量约为 40 kg (88 lb)。
- 拆下将飞轮固定在曲轴上的其余四个螺栓。
- 拆下飞轮 (1) 。
- 将齿轮 (4) 从飞轮 (1) 上拆下。
Show/hide table
图 3 | g01951608 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | FT-0120     | 提升支架     | 1     |
B     | -     | 导向螺柱 5/8 - 18 x 6 in     |
2     |
- 将齿轮 (4) 加热到最大温度 320° C (610° F)。 将齿轮 (4) 安装在飞轮 (1) 上。
Show/hide table
图 4 | g01951608 |
注: 当您安装齿轮 (4) 时,斜面一侧必须远离飞轮 (1) 。
- 将工具 (B) 安装在曲轴中。
Show/hide table
图 5 | g01951606 |
- 将工具 (A) 和适当的提升设备连接到飞轮 (1) 上。 飞轮 (1) 的重量约为 40 kg (88 lb)。
- 将飞轮 (1) 安置在工具 (B) 上,然后将飞轮滑入位置。
- 安装底部的四个螺栓。
- 确保螺纹孔 (2) 位于顶部。
Show/hide table
图 6 | g01951604 |
- 拆下工具 (A) 和工具 (B) 。
- 安装将飞轮 (1) 固定在位的其余螺栓 (3) 。
Caterpillar Information System:
C13 Industrial Engines Electronic Unit Injector
C175 Generator Sets Generator Operation
2010/10/08 Proper Placement of the Speed Control for Some Gas Engines {1264, 1716, 1908}
2009/08/17 A New Hose Assembly for the Coolant Outlet from the Turbocharger Is Used on Some 3508B and 3512B Engines {1355, 1380, 1393}
C7.1 Industrial Engine and Generator Set Injector Code - Calibrate
797F and 797F XQ Off-Highway Truck Power Train Differential
797F and 797F XQ Off-Highway Truck Steering System Solenoid Valve (Steering)
797F and 797F XQ Off-Highway Truck Steering System Solenoid and Relief Valve (Steering)
C7.1 Industrial Engine and Generator Set Diesel Particulate Filter Collects Excessive Soot
797F and 797F XQ Off-Highway Truck Power Train Relief Valve (Transmission Main)
797 Off-Highway Truck Braking System Service and Parking Brake (Rear)
797F and 797F XQ Off-Highway Truck Power Train Torque Converter Housing
G3512E and G3520E Generator Set Engines Electronic Control System Parameters
G3304B and G3306B Engines Flywheel Housing - Remove
C175-16 Locomotive Engine Engine Governing - Adjust
797F and 797F XQ Off-Highway Truck Power Train Transmission Hydraulic Control
C13, C15, and C18 Tier 4 Interim Engines ARD Is Disabled
G3304B and G3306B Engines Flywheel Housing - Install
C13 Tier 4 Final Engines Electronic Unit Injector Mechanism
C9.3 Marine Propulsion Engine Decommissioning and Disposal
G3304B and G3306B Engines Water Directors - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
G3304B and G3306B Engines Crankshaft Front Seal and Wear Sleeve - Remove
C15 and C18 Industrial Engines Inlet and Exhaust Valves - Remove and Install