Fan - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 140-7742     | 套筒     | 1     |
开始:
- 释放液压系统压力。 请参阅拆解和组装, "液压系统压力 - 释放"。
注: 为便于安装,在所有管路、软管、导线及管上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和有助于防止机油系统污染。
- 从冷却系统将发动机冷却液排入合适的容器,进行以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却(ELC)- 更换"。
- 将液压油排入适当的容器以便保存或处理。 请参阅操作和保养手册, "加注容量"。
- 卸下挡板 (1) 。
Show/hide table
图 1 | g01708314 |
- 打开左侧的前检测门,找到螺栓 (2) 。 卸下螺栓 (2) 。 打开检修门 (3) 。
Show/hide table
图 2 | g01708316 |
- 将合适的起吊设备连接到发动机罩组件 (4) 上。 发动机罩组件 (4) 的重量约为 68 kg (150 lb)。 卸下螺栓 (5) 。 拆下发动机罩组件 (4) 。
Show/hide table
图 3 | g01708317 |
- 拆下支承 (9) 。 断开软管 (7) 和 (8) 。 将软管 (8) 从风扇组件 (10) 上断开。 拆卸管 (6) 和 (11) 。
Show/hide table
图 4 | g01708320 |
- 将管 (12) 作为一个整体进行拆卸。
Show/hide table
图 5 | g01708324 |
- 拆下盖 (13) 。 断开软管组件 (14) 。
Show/hide table
图 6 | g01708327 |
- 卸下支架 (15) 。
Show/hide table
图 7 | g01708329 |
- 拆下支架 (16) 。 对另一侧重复此操作。
Show/hide table
图 8 | g01708331 |
- 拆下螺栓 (17) 和风扇组件 (10) 。
Show/hide table
图 9 | g01708334 |
- 将工具 (A) 和适当的起吊设备固定到风扇组件 (10) 上。 风扇组件 (10) 的重量约为 159 kg (350 lb)。
Show/hide table
图 10 | g01708335 |
Show/hide table
图 11 | g01708336 |
- 拆下螺栓 (18) 。 对另一侧重复此操作。
- 拆下风扇组件 (10) 。
- 拆下罩 (19) 。
Show/hide table
图 12 | g01708338 |
- 将工具 (A) 和合适的起吊设备连接到十字轴组件 (20) 。 十字轴组件 (20) 的重量大约为 45 kg (100 lb)。
Show/hide table
图 13 | g01708339 |
- 拆下螺栓 (21) 和十字轴组件 (20) 。
Caterpillar Information System:
Plugging of the In-line Fuel Filters for the Aftertreatment Regeneration Device (ARD){108M, 1261, 3206} Plugging of the In-line Fuel Filters for the Aftertreatment Regeneration Device (ARD){108M, 1261, 3206}
2008/10/06 New Improved Fuel Injectors Are Now Used {1251, 1290}
3516B Power Package Maintenance Interval Schedule
345D and 349D Excavators C13 Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Assemble
345D and 349D Excavators C13 Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Disassemble
C6.6 Marine Generator Set Engine Oil Filter Base - Remove and Install - MCS Engine Oil Filter Base
C6.6 Marine Generator Set Fuel Filter Base - Remove and Install - MCS Secondary Fuel Filter
G3304 and G3306 Engines Exhaust Manifold
C6.6 Marine Generator Set Fuel Filter Base - Remove and Install - MCS Primary Fuel Filter
3500 Generator Sets Configuration Parameters
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System Electronic Control Unit - Replace
C4.4 Generator Set Engines CID 0247 FMI 12
795F AC and 795F AC XQ Off-Highway Trucks Ether Starting Aid Cylinder - Replace
2008/09/29 A New Type of Main Bearing is Available {1202, 1203}
2008/10/01 A New Type of Main Bearing is Available {1202, 1203}
Location Updates Are Not Being Reported From The Product Link PL321{7606} Location Updates Are Not Being Reported From The Product Link PL321{7606}
C6.6 Marine Generator Set Heater Mounting Group - 240 Volt
C6.6 Marine Generator Set Heater Mounting Group - 110 Volt
C6.6 Marine Generator Set Control System - Remove and Install - M.C.S Panel
C6.6 Marine Generator Set Fuel Injection Lines
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Bucket Cylinder - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Load Control Valve (Boom Lowering) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Load Control Valve (Boom Cylinder) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Boom Cylinder - Remove and Install