Load Control Valve (Boom Lowering) - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | FT-2674     | 真空舱     | 1     |
开始:
- 释放系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
注: 在所有软管、所有软管组件、所有导线及所有管组件上作出识别标记,以便安装。 插接好所有软管组件和所有管组件。 这将有助于防止液体渗漏,并有助于防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 液压系统被异物污染会缩短液压系统部件的使用寿命。 为了避免污染物进入液压系统,总要在断开后塞住或盖住管路、管接头或软管。 罩住已解体的部件,然后在组装前正确清洁它们。 在更换任何主部件后,或特别是在部件故障后,正确清洁液压系统,以便去除全部污染物。 |
- 将工具 (A) 安装到液压油箱上。 将一条供气软管连接到工具 (A) 上。 施加 276 至 414 kPa (40 至 60 psi) 的气压。 此步骤将使液压系统处于真空状态。
Show/hide table
图 1 | g01196137 |
- 断开软管组件 (1) 、 (3) 和 (4) 。 拆下负载控制阀 (2) 。
Show/hide table
图 2 | g01198865 |
Caterpillar Information System:
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Bucket Cylinder - Remove and Install
C6.6 Marine Generator Set Fuel Injection Lines
C6.6 Marine Generator Set Control System - Remove and Install - M.C.S Panel
C6.6 Marine Generator Set Heater Mounting Group - 110 Volt
C6.6 Marine Generator Set Heater Mounting Group - 240 Volt
Location Updates Are Not Being Reported From The Product Link PL321{7606} Location Updates Are Not Being Reported From The Product Link PL321{7606}
2008/10/01 A New Type of Main Bearing is Available {1202, 1203}
2008/09/29 A New Type of Main Bearing is Available {1202, 1203}
795F AC and 795F AC XQ Off-Highway Trucks Ether Starting Aid Cylinder - Replace
345D and 349D Excavators C13 Engine Supplement Fan - Remove
Plugging of the In-line Fuel Filters for the Aftertreatment Regeneration Device (ARD){108M, 1261, 3206} Plugging of the In-line Fuel Filters for the Aftertreatment Regeneration Device (ARD){108M, 1261, 3206}
2008/10/06 New Improved Fuel Injectors Are Now Used {1251, 1290}
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Load Control Valve (Boom Cylinder) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Boom Cylinder - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Boom - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Counterbalance Valve (Travel) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swivel - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swing Cushion Valve - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swing Motor - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Hydraulic Tank and Filter - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Counterweight Cylinder - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Control Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Check Valve (Counterweight Circuit) - Remove
G3304 and G3306 Engines Magneto