Boom - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 9U-6225     | 销冲头盖     | 1     |
B     | 1U-9204     | 操纵杆滚轮起重机     | 1     |
C     | 3S-6224     | 电动液压泵总成     | 1     |
6V-0014 | 液压油缸总成     | 1     | |
141-1785 | 接收套筒     | 1     | |
9U-6810 | 螺母     | 1     | |
9U-6815 | 拉拔器螺柱     | 1     | |
D     | FT-2674     | 真空舱     | 1     |
开始:
- 拆下斗杆。 请参阅拆解和组装, "斗杆 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
在工作温度下,液压油温度很高且处于压力下。 热机油能造成烫伤。 为避免可能的人身伤害,在断开或拆下任何液压管路或部件之前,请释放作业机具液压回路(动臂、斗杆、铲斗和回转机构)、行驶回路及液压油箱加注口盖处的压力。 仅当发动机停止并且加注口盖冷却到可以接触时方可拆下加注口盖。 |
- 将动臂降到地面上。
- 释放系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
- 断开润滑脂软管组件 (1) 。
Show/hide table
图 1 | g00574959 |
- 将适当的起吊设备连接到动臂油缸 (4) 。 动臂油缸 (4) 的重量约为 440 kg (970 lb)。
Show/hide table
图 2 | g00574971 |
- 卸下螺栓 (2) 。 拆下挡板 (3) 和隔套。
- 重复步骤 5 以拆卸相对动臂油缸的挡板。
- 将工具 (A) 安装到销 (5) 中。 使用锤将销 (5) 打出动臂油缸 (4) 。
Show/hide table
图 3 | g01206155 |
- 断开润滑脂软管组件 (6) 。 重复步骤4至7,以将动臂油缸从另一侧断开。
Show/hide table
图 4 | g00628478 |
- 拆下梯子 (7) 。
Show/hide table
图 5 | g01206158 |
- 将工具 (A) 安装到液压油箱上。 将一条供气软管连接到工具 (A) 上。 施加 276 至 414 kPa (40 至 60 psi) 的气压。 此步骤将使液压系统处于真空状态。
Show/hide table
图 6 | g01196137 |
- 断开三个软管组件 (8) 。 断开四个软管组件 (9) 。 断开四个软管组件 (11) 。 断开线束组件 (10) 。
Show/hide table
图 7 | g01206159 |
- 断开两个软管组件 (12) 。
Show/hide table
图 8 | g01206160 |
- 将挡板 (3) 和螺栓 (2) 安装在销 (5) 两侧。 安装销组件 (15) 和螺栓 (14) 。
Show/hide table
图 9 | g01206161 |
Show/hide table
图 10 | g01206162 |
注: 确保销 (5) 处于动臂销孔的中心位置。
- 将工具 (B) 和适当的起吊设备连接到动臂 (13) 。 动臂 (13) 的重量范围可能约为 4000 kg (8820 lb) 至 4600 kg (10140 lb)。
- 将适当的起吊设备连接到工具 (C) 上。 工具 (C) 的重量约为 191 kg (420 lb)。 将工具 (C) 连接到销组件 (16) 。
Show/hide table
图 11 | g01206263 |
Show/hide table
图 12 | g01206265 |
- 拆下螺栓 (17) 。 使用工具 (C) 卸下销组件 (16) 。 拆下销组件 (16) ,直到动臂从上部机架中脱离。 销组件 (16) 的重量约为 122 kg (270 lb)。
注: 拆下销组件 (16) 后,重新定位适当的起吊设备。
- 拆卸动臂和垫片。 在垫片上作识别标记,以便于组装。
Caterpillar Information System:
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Boom Cylinder - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Load Control Valve (Boom Cylinder) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Load Control Valve (Boom Lowering) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Bucket Cylinder - Remove and Install
C6.6 Marine Generator Set Fuel Injection Lines
C6.6 Marine Generator Set Control System - Remove and Install - M.C.S Panel
C6.6 Marine Generator Set Heater Mounting Group - 110 Volt
C6.6 Marine Generator Set Heater Mounting Group - 240 Volt
Location Updates Are Not Being Reported From The Product Link PL321{7606} Location Updates Are Not Being Reported From The Product Link PL321{7606}
2008/10/01 A New Type of Main Bearing is Available {1202, 1203}
2008/09/29 A New Type of Main Bearing is Available {1202, 1203}
795F AC and 795F AC XQ Off-Highway Trucks Ether Starting Aid Cylinder - Replace
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Counterbalance Valve (Travel) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swivel - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swing Cushion Valve - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swing Motor - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Hydraulic Tank and Filter - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Counterweight Cylinder - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Control Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Check Valve (Counterweight Circuit) - Remove
G3304 and G3306 Engines Magneto
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Manual Ball Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Solenoid Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Shuttle Valve (Counterweight Circuit) - Remove