Swivel - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | FT-2674     | 真空舱     | 1     |
B     | 1U-7505     | 液压千斤顶     | 1     |
C     | 138-7575     | 连杆支架     | 2     |
开始:
- 释放系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将工具 (A) 安装到液压油箱上。 将一条供气软管连接到工具 (A) 上。 施加 276 至 414 kPa (40 至 60 psi) 的气压。 此步骤将使液压系统处于真空状态。
- 将工具 (B) 定位在防护装置 (1) 之下。 卸下螺栓 (2) 。 拆下防护装置 (1) 。 每个防护装置 (1) 的重量约为 25 kg (55 lb)。
注: 防护装置 (1) 顶部的碎屑可能会使防护装置 (1) 的重量增加。
Show/hide table
图 1 | g01216634 |
- 断开软管组件 (3) 。 断开软管组件 (4) 。 断开软管组件 (5) 。 拆下接头 (6) 。 拆下螺栓 (7) 。
Show/hide table
图 2 | g01214327 |
- 断开软管组件 (8) 、 (9) 、 (10) 和 (11) 。 拆下支承 (12) 。
Show/hide table
图 3 | g01214329 |
- 拆下螺栓 (13) 。 拆下护圈 (14) 。 拆下卡箍 (15) 。 拆下罩 (16) 。 将工具 (C) 和适当的起吊设备安装在旋转接头 (17) 上。 拆下旋转接头 (17) 。 旋转接头 (17) 的重量约为 50 kg (110 lb)。
Show/hide table
图 4 | g01214330 |
Caterpillar Information System:
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Counterbalance Valve (Travel) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Boom - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Boom Cylinder - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Load Control Valve (Boom Cylinder) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Load Control Valve (Boom Lowering) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Bucket Cylinder - Remove and Install
C6.6 Marine Generator Set Fuel Injection Lines
C6.6 Marine Generator Set Control System - Remove and Install - M.C.S Panel
C6.6 Marine Generator Set Heater Mounting Group - 110 Volt
C6.6 Marine Generator Set Heater Mounting Group - 240 Volt
Location Updates Are Not Being Reported From The Product Link PL321{7606} Location Updates Are Not Being Reported From The Product Link PL321{7606}
2008/10/01 A New Type of Main Bearing is Available {1202, 1203}
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swing Cushion Valve - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Swing Motor - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Hydraulic Tank and Filter - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Counterweight Cylinder - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Control Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Check Valve (Counterweight Circuit) - Remove
G3304 and G3306 Engines Magneto
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Manual Ball Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Solenoid Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Shuttle Valve (Counterweight Circuit) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Gear Pump (Auxiliary) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Pump Drive Group - Remove - Auxiliary