Engine Oil Filter Base - Remove and Install - MCS Engine Oil Filter Base
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 185-3630 | Strap Wrench As | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
Note: Identify the position on the tube assembly in order to show the correct position of the tube assembly. Plug all tube assembly. Cap all connections on the oil filter base assembly.
- The engine can have the ability to auto start. Ensure that the power supply is isolated before any service or repairs is performed.
Show/hide table
Illustration 1 g01661735 - Use Tooling (A) to remove engine oil filters (6). Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".
- Disconnect hose assembly (1) and hose assembly (2) from oil filter base (2).
Note: Plug hose assemblies. Cap all connections on the oil filter base assembly.
- Remove bolts (3) from oil filter base (2).
- Remove oil filter base (2) from bracket (5).
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the oil filter base is clean and free from wear or damage. If necessary, replace the oil filter base.
- Position oil filter base (4) onto bracket (5).
- install bolts (3) to oil filter base (2). Tighten the bolts to a torque of
44 N·m (33 lb ft) . - Remove the plugs from hose assemblies. Remove the cap from connections on the oil filter base assembly. Connect hose assembly (1) and hose assembly (2). Tighten hose assemblies securely.
- Install a new engine oil filter (6) and check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.
Show/hide table
| |
| Illustration 2 | g01661735 |
Caterpillar Information System:
C6.6 Marine Generator Set Fuel Filter Base - Remove and Install - MCS Secondary Fuel Filter
G3304 and G3306 Engines Exhaust Manifold
C6.6 Marine Generator Set Fuel Filter Base - Remove and Install - MCS Primary Fuel Filter
3500 Generator Sets Configuration Parameters
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System Electronic Control Unit - Replace
C4.4 Generator Set Engines CID 0247 FMI 12
C4.4 Generator Set Engines CID 0247 FMI 09
C175-16 Marine Engines Maintenance Recommendations
C4.4 Generator Set Engines Can Not Reach Top Engine RPM
C4.4 Generator Set Engines Sensors and Electrical Connectors
345D and 349D Excavators C13 Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
345D and 349D Excavators C13 Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Install
345D and 349D Excavators C13 Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Disassemble
345D and 349D Excavators C13 Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Assemble
3516B Power Package Maintenance Interval Schedule
2008/10/06 New Improved Fuel Injectors Are Now Used {1251, 1290}
Plugging of the In-line Fuel Filters for the Aftertreatment Regeneration Device (ARD){108M, 1261, 3206} Plugging of the In-line Fuel Filters for the Aftertreatment Regeneration Device (ARD){108M, 1261, 3206}
345D and 349D Excavators C13 Engine Supplement Fan - Remove
795F AC and 795F AC XQ Off-Highway Trucks Ether Starting Aid Cylinder - Replace
2008/09/29 A New Type of Main Bearing is Available {1202, 1203}
2008/10/01 A New Type of Main Bearing is Available {1202, 1203}
Location Updates Are Not Being Reported From The Product Link PL321{7606} Location Updates Are Not Being Reported From The Product Link PL321{7606}
C6.6 Marine Generator Set Heater Mounting Group - 240 Volt
C6.6 Marine Generator Set Heater Mounting Group - 110 Volt