Flywheel Housing
Show/hide table
| |
| Illustration 1 | g02568161 |
|
Rear view | |
Show/hide table
| |
| Illustration 2 | g02568076 |
|
Tightening sequence | |
Show/hide table
| Specification for 239-3646 Flywheel Housing Gp | |||
| Item | Qty | Part | Specification Description |
| - | - | - | Before installation of the flywheel housing, inspect the front face of the flywheel housing and the rear face of the rear housing. The components must be free of the following substances: oil, fuel, water, assembly compounds, and any other contaminants. |
| - | - | - | Check assembled installation depth of the crankshaft seal group with the crankshaft at maximum rearward position. |
| - | - | - | Use the following procedure to tighten the flywheel housing bolts. Tighten the bolts in the numerical sequence as shown in the Illustration 2. |
| 1 | 2 | 245-3803 Bolt | Tighten bolt (1) through bolt (2) to |
| 2 | 8 | 2H-6488 Bolt | Tighten bolt (3) through bolt (10) to |
| 3 | 24 | 0L-1143 Bolt | Tighten bolt (11) through bolt (34) to |
| 4 | - | - | The seal and the sleeve of the crankshaft seal group must not be used if the seal and the sleeve have been separated. |
| The seal driver must not contact the seal within the |
|||
| A | - | - | Distance from the sleeve to the seal is |
| C | - | - | Installation depth of the sleeve from the rear face of the crank shaft is |
Caterpillar Information System:
C6.6 Marine Generator Set Data Link Circuit - Test
G3412C, G3508, G3512 and G3516 Engines Status Control Module Alarm Modules
C18 Generator Set Engine Air Cleaner Service Indicator - Inspect
C27 and C32 Engines for Caterpillar Built Machines Housing (Rear)
C12 Marine Engines Configuration Parameters
325D and 329D Excavators and 325D Material Handler Machine System Specifications Pressure Reducing Valve (Boom Priority)
2008/07/01 New Hose and Clamps are Now Available on Clean Gas Induction (CGI) Coolers {1061, 1087, 108C, 1380}
Installation of the 276-7630 Turbocharger Shield Group {1073} Installation of the 276-7630 Turbocharger Shield Group {1073}
2008/08/25 A New Fuel Pressure Regulator Is Used {1252, 1254}
3508B, 3508C, 3512B, 3512C, 3516B and and 3516C Marine Engines Safety Messages
2015/04/03 Recommendations for Battery Charging for Genset Usage {1401, 1406}
G3412C, G3508, G3512 and G3516 Engines Status Control Module Sensor
2008/07/07 Fuel Transfer Pump {1251}
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Product Lifting
G3520E Generator Set Engines Vibration Damper
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Customer Assistance
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator Set Vibration - Inspect
C6.6 Marine Generator Set System Pressure Release
2008/07/28 New Fuel Lines Groups are Now Available {1274}
2008/07/07 New Starter Lines Group and Prelube Pump Group Are Used {1319, 1451}
C18 Generator Set Engines Configuration Parameters
3512B Generator Set Engine Fuel Filter
3500B Locomotive Engines Exhaust Manifold
793F and 797F Off-Highway Trucks Power Train Electronic Control System Switch Circuits