Tilt Cylinder - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 350-7768 | 电动液压泵总成 (115V) | 1 |
350-7769 | 电动液压泵总成 (230V) | 1 | |
6V-3175 | 双作用油缸 | 1 | |
9U-5266 | 套筒 | 1 | |
4C-9634 | 拉拔器螺柱 | 1 | |
9U-6832 | 螺母 | 1 | |
3H-0467 | 拉拔器垫圈 | 1 |
开始:
- 释放系统压力。
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
配备锁止阀的油缸即使在软管拆卸后也会长时间保持高压状态。 如果拆卸锁止阀或解体油缸之前没有释放所有压力,则可能会导致人身伤亡。 拆卸锁止阀或解体油缸之前确保释放所有压力。 |
Show/hide table
当您使用液压油缸和拉拔器螺柱时,务必确保拉拔器螺柱的额定容量达到或超过液压油缸的额定容量。 如果拉拔器螺柱未达到或超过液压油缸的额定容量,拉拔器螺柱可能突然发生故障。 拉拔器螺柱的突然故障可能导致人身伤亡。 |
- 断开软管组件 (1) 和 (2)。
Show/hide table
图 2 g01292971 - 断开线束组件 (4)。 拆下夹子 (3) 和 (5)。
Show/hide table
图 3 g06112166 - 将适当的起吊设备连接到倾斜油缸 (8) 上。 倾斜油缸 (8) 的重量约为
125 kg (275 lb) 。 - 拆下螺栓 (6)(未显示)。 使用工具 (A) 拆下销组件 (7)(未显示)。 由两人或使用适当的起吊设备拆下销组件 (7)。 带工具 (A) 的销组件 (7) 的重量约为
25 kg (55 lb) 。 - 拆下螺栓 (10)。 使用工具 (A) 拆下销组件 (9)。 由两人或使用适当的起吊设备拆下销组件 (9)。销组件 (9) 与工具 (A) 的重量约为
25 kg (55 lb) 。 - 拆下倾斜油缸 (8)。 拆下任何存在的垫片。
Show/hide table
图 1 | g01292951 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 350-7768 | 电动液压泵总成 (115 V) | 1 |
350-7769 | 电动液压泵总成 (230 V) | 1 | |
6V-3175 | 双作用油缸 | 1 | |
4C-9634 | 拉拔器螺柱 | 1 | |
9U-6832 | 高速螺母组件 | 1 | |
5P-8601 | 轴承拆卸工具适配器 | 1 | |
7F-6068 | 套筒组件 | 1 | |
B | - | Loctite 263 | - |
C | - | Loctite 固定剂 | - |
D | - | SAE 10W 液压油 | - |
Show/hide table
配备锁止阀的油缸即使在软管拆卸后也会长时间保持高压状态。 如果拆卸锁止阀或解体油缸之前没有释放所有压力,则可能会导致人身伤亡。 拆卸锁止阀或解体油缸之前确保释放所有压力。 |
Show/hide table
图 4 | g01291218 |
注: 工具 (A) 用于拆卸和安装轴承 (4) 和 (6)。
(1) 将工具 (B) 涂覆到挡圈的螺纹上。 固定器的扭矩 ...
(2) 使用所密封的润滑剂稍微润滑密封件。
(3) 将工具 (C) 涂覆到刮油密封的槽上。
(5) 将工具 (B) 和工具 (D) 涂覆到锁紧螺母的螺纹上。 锁紧螺母扭矩 ...
- 按与拆卸相反的顺序安装倾斜油缸 (8)。
- 安装销组件 (9) 和 (7) 的垫片,使总间隙不超过
1.80 mm (0.071 inch) 。
- 安装销组件 (9) 和 (7) 的垫片,使总间隙不超过
Caterpillar Information System:
D5R and D6N Track-Type Tractor Engine Supplement Cooling System Package (Radiator, Aftercooler, Oil Cooler) - Assemble
D7E Track-Type Tractor Current Sensor - Test
854K Wheel Dozer Declaration of Conformity
992K Wheel Loader Declaration of Conformity
390F Excavator Machine System Final Drive and Motor Fastener (Mounting)
910M, 914M, 918M, 910K, and 914K Wheel Loader Machine Systems Lift Cylinder - Remove and Install
953K Track-Type Loader Machine Systems Bucket Lever and Link - Remove and Install
D5R and D6N Track-Type Tractor Engine Supplement Cooling System Package (Radiator, Aftercooler, Oil Cooler) - Disassemble
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Lubrication
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Torque Converter Stall and Implement Pump Double Stall - Test
390F Excavator Machine System Front Idler
C4.4 and C6.6 Engines Coolant Level Is Low
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Fuel Consumption Is Excessive
D6T XE Electrical & Hydraulic Troubleshooting Current Sensor - Test
Check the Air Conditioner Compressor Mount on AD45B Underground Articulated Trucks {1802} Check the Air Conditioner Compressor Mount on AD45B Underground Articulated Trucks {1802}
340F Excavator Machine Systems Boom Lines
C1.7 and C2.2 Industrial Engines Cylinder Head - Inspect
C1.7 and C2.2 Industrial Engines Engine Valve Lash - Inspect/Adjust
C1.7 and C2.2 Industrial Engines General Information
C1.7 and C2.2 Industrial Engines Electronic Control System Components
Installing the Conversion Harness for Non-Cat Hydromechanical (Simple) Work Tools {1408} Installing the Conversion Harness for Non-Cat Hydromechanical (Simple) Work Tools {1408}
Installing the Conversion Harness for non-Cat Hydromechanical (Complex) Work Tools {1408} Installing the Conversion Harness for non-Cat Hydromechanical (Complex) Work Tools {1408}
D6T Track Type Tractor Power Train Torque Converter - Disassemble
3516E Engines for Caterpillar Built Machines Turbocharger - Remove and Install