Engine Cranks but Does Not Start
- Fuel Supply
- Engine Shutdown Switches (if applicable)
- Starting Aids (if applicable)
- Air Inlet and Exhaust System
- Theft Deterrent System (if applicable)
- Sensors
- Engine Speed/Timing
- Fuel System
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. Inspection of the Fuel Supply A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only. B. Ensure that the fuel supply valve (if equipped) is in the full OPEN position. |
Fuel level |
Result: The fuel level is OK. Proceed to Test Step 2. Result: The fuel level is not OK. Repair: Fill the tank. |
2. Engine Shutdown Switches (if applicable) A. The engine shutdown switches must be in the OFF position. B. Use Cat ET to verify the status of the engine shutdown switches. When a shutdown occurs, the keyswitch must be turned to the OFF position for at least 15 seconds before restarting the engine. |
Switches are in the OFF position |
Result: The switches are in the OFF position. Proceed to Test Step 3. Result: The switches are not in the OFF position. Repair: Turn the switches to the OFF position. |
3. Starting Aids (if applicable) If cold ambient conditions exist, check the operation of the starting aids. Verify that the starting aid is operating correctly. |
Starting aids are operational |
Result: The starting aid is operating correctly. Proceed to Test Step 4. Result: The starting aid is not operating correctly. Repair: Refer to the appropriate circuit test in order to troubleshoot the starting aid. |
4. Restrictions in the Air Inlet and Exhaust System A. Check for an air filter restriction indicator. B. Check the air inlet and exhaust system for restrictions and/or leaks. |
Air and Exhaust System restrictions |
Result: There are no system restrictions. Proceed to Test Step 5. Result: There are system restrictions. Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System" for additional information on the air inlet and exhaust systems. Repair: Replace plugged air filters. Refer to the Operation and Maintenance Manual for the correct procedure. |
5. Theft Deterrent System (if applicable) A. Verify that the theft deterrent system is not active. |
Theft system is inactive. |
Result: The theft deterrent system is not active. Proceed to Test Step 6. Result: The theft deterrent system is active. Repair: Turn the theft deterrent system OFF. |
6. Sensors A. The coolant temperature sensor must provide a correct signal in order for cold mode operation to operate correctly. Refer to "Cold Mode Operation" within the Systems Operation, "General Information". B. Verify that the coolant temperature on Cat ET is reasonable for the conditions that are present. |
Sensor output |
Result: The sensor is operating properly. Proceed to Test Step 7. Result: The sensor is not operating properly. Repair: Refer to Troubleshooting, "Sensor Signal (Analog, Passive) - Test" for troubleshooting information. |
7. Engine Speed/Timing A. Crank the engine and observe the engine speed on the Cat ET status screen. Refer to Troubleshooting, "Speed/Timing - Test" for additional information. Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message will be replaced with an engine speed once the ECM is able to calculate a speed from the signal. |
Timing signal |
Result: The timing sensor is operating properly. Proceed to Test Step 8. Result: The timing sensor is not operating properly. Repair: Refer to Troubleshooting, "Speed/Timing - Test" for troubleshooting information. |
8. Fuel System A. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information. B. Cold weather adversely affects the characteristics of the fuel. Refer to the engines Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation. C. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply. D. Check the filtered fuel pressure while the engine is being cranked. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for the test procedure and for the correct pressure values. If the fuel pressure is low, replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details. E. Check for the proper operation of the fuel transfer pump. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for test information. |
Low-pressure fuel system |
Result: The low-pressure fuel system is not operating properly. Repair: Make the necessary repairs. Return the engine to service. |
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Cylinder Is Noisy
834K Wheel Dozer Diesel Exhaust Fluid Filter - Replace - Emission Related Component
2014/11/26 New Separate Circuit Vent Lines Check Valve Is Now Available on Certain D7E Track-Type Tractors {1377, 1380}
C27 and C32 Engines for Caterpillar Built Machines Crankcase Pressure Is High
D7E Track-Type Tractor Power Train Pivot Shaft - Remove and Install
312F GC and 313F GC Excavators Machine Systems Boom Drift Reduction Valve
D7E Track-Type Tractor Power Train Track Roller Frame - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Coolant Contains Fuel
C27 and C32 Engines for Caterpillar Built Machines Coolant Contains Oil
C27 and C32 Engines for Caterpillar Built Machines Alternator Problem - Charging Problem and/or Noisy Operation
926M, 930M and 938M Wheel Loaders Machine Systems Lift Cylinder - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Sensor Signal (Analog, Passive) - Test
335F Excavator Engine Oil and Filter - Change
335F Excavator Engine Oil Sample - Obtain
335F Excavator Safety Messages
D7E Track-Type Tractor Systems Equalizer Bar
D7E Track-Type Tractor Systems Oil Filter (Power Train)
D7E Track-Type Tractor Systems Angling Bulldozer
D7E Track-Type Tractor Systems Hydraulic Tank and Filter
D6T Track-Type Tractor Systems Piston Motor (Fan Drive)
D7E Track-Type Tractor Systems Tilt Cylinder (Bulldozer)
926M, 930M and 938M Wheel Loaders Machine Systems Electrohydraulic Control (Joystick) - Remove and Install
D7E Track-Type Tractor Systems Pilot Lines
926M, 930M and 938M Wheel Loaders Machine Systems Instrument Panel - Remove and Install