Track Roller Frame - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 350-7768 | Electric Hydraulic Pump Gp 115V | 1 |
305-7769 | Electric Hydraulic Pump Gp 230V | 1 | |
8S-7610 | Base As | 1 | |
8S-7650 | Cylinder As | 2 | |
8S-7615 | Pins | 2 | |
B | 8S-7640 | Stands | 2 |
8S-7611 | Tubes | 2 | |
8S-7615 | Pins | 2 | |
C | 189-0410 | Shackle As | 4 |
D | 8B-7557 | Threaded Adapter | 1 |
1P-0074 | Slide Hammer Puller Gp | 1 | |
E | 386-6032 | Lever Puller Hoist | 1 |
F | 386-6030 | Lever Puller Hoist | 1 |
G | 439 - 3941 | Link Brackets | 4 |
Start By:
- Remove the blade.
- Separate the track.
- Use Tooling (A) in order to raise the machine. Raise the machine in order to lift the track roller frame off the track. Use Tooling (B) in order to support the machine.
Show/hide table
Illustration 2 g03748386 - Attach Tooling (C) and a suitable lifting device to track roller frame (1). The weight of track roller frame (1) is approximately
2340 kg (5160 lb) . Remove bolts (2). Remove caps (3).Show/hide tableIllustration 3 g01897654 Typical Example - Remove guards (6).
- Remove sprocket segment (4). Refer to Disassembly and Assembly , "Sprocket Segment - Remove and Install". Remove plate (5).
Show/hide table
Illustration 4 g01897673 - Use Tooling (D) in order to remove retainer (7).
Show/hide table
Illustration 5 g03757639 Typical Example - Attach Tooling (G), Tooling (E), Tooling (F), and a suitable lifting device to track roller frame (1). The weight of track roller frame (1) is approximately
2340 kg (5160 lb) .Show/hide tableIllustration 6 g01897717 - Remove bolts (8). Remove plate (9).
Show/hide table
Illustration 7 g01897659 - Remove thrust washer (10). Remove the track roller frame.
Show/hide table
Illustration 8 g01910005 - Remove seal (11).
Show/hide table
Illustration 9 g01897719 Show/hide tableIllustration 10 g01897722 - Remove bearings (12) and (13) from the track roller frame.
Show/hide table
Illustration 1 | g01885073 |
- Install track roller frame (1) in the reverse order of removal.
- Lubricate seal (11) with lubricant that is being sealed.
- Tighten bolts (8) to a torque of
300 ± 40 N·m (220 ± 30 lb ft) . - Tighten bolts (2) to a torque of
900 ± 100 N·m (664 ± 74 lb ft) .
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Coolant Contains Fuel
C27 and C32 Engines for Caterpillar Built Machines Coolant Contains Oil
C27 and C32 Engines for Caterpillar Built Machines Alternator Problem - Charging Problem and/or Noisy Operation
926M, 930M and 938M Wheel Loaders Machine Systems Lift Cylinder - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Sensor Signal (Analog, Passive) - Test
C27 and C32 Engine for MD6250 and MD6310 Drill Timing - Calibrate
C27 and C32 Engines for Caterpillar Built Machines Sensor Signal (Analog, Active) - Test
C280 Marine Engines DEF Pump Motor - Test
D7E Track-Type Tractor Systems ROPS Group
D7E Track-Type Tractor Systems Sprocket Segment
D7E Track-Type Tractor Systems Refrigerant Condenser and Mounting
D7E Track-Type Tractor Systems Pump Control Valve (Steering)
312F GC and 313F GC Excavators Machine Systems Boom Drift Reduction Valve
D7E Track-Type Tractor Power Train Pivot Shaft - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Crankcase Pressure Is High
2014/11/26 New Separate Circuit Vent Lines Check Valve Is Now Available on Certain D7E Track-Type Tractors {1377, 1380}
834K Wheel Dozer Diesel Exhaust Fluid Filter - Replace - Emission Related Component
C27 and C32 Engines for Caterpillar Built Machines Cylinder Is Noisy
C27 and C32 Engines for Caterpillar Built Machines Engine Cranks but Does Not Start
335F Excavator Engine Oil and Filter - Change
335F Excavator Engine Oil Sample - Obtain
335F Excavator Safety Messages
D7E Track-Type Tractor Systems Equalizer Bar
D7E Track-Type Tractor Systems Oil Filter (Power Train)