Camshaft - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-7638     | Magnetic Holding Tool     | 18     |
B     | 201-4211     | Camshaft Pilot     | 1     |
201-4212 | Camshaft Pilot     | 1     |
- Install Tooling (B) .
Note: Ensure that camshaft (6) and Tooling (B) are clean. Apply clean engine oil to the lobes and journals of camshaft (6) and Tooling (B) .
Show/hide table
Illustration 1 | g01292428 |
- Carefully install camshaft (6) in the engine.
Note: During installation of camshaft (6), rotate the camshaft in both directions in order to prevent binding in the camshaft bearing bores.
- Ensure that the timing Marks (X) on the idler gear are aligned with the timing marks on the crankshaft gear and the camshaft drive gear.
Show/hide table
NOTICE |
---|
When installing the camshaft, make sure the number one cylinder is at top center of the compression stroke with the timing bolt installed in the flywheel. The camshaft timing is very important. The timing mark on the camshaft drive gear must line up with the timing mark on the idler gear. Refer to the Specifications Manual for more information. |
Show/hide table
Illustration 2 | g01292427 |
- Remove Tooling (A) and Tooling (B) .
- Position cover (3) and install bolts (2) .
Show/hide table
Illustration 3 | g01372193 |
- Install tube assemblies (4) .
- Install bolts (1) .
Show/hide table
Illustration 4 | g01011039 |
End By:
- Install the camshaft position sensor. Refer to Disassembly and Assembly, "Camshaft Position Sensor - Remove and Install".
- Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
- Install the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install".
Caterpillar Information System:
C13 Engine Camshaft - Remove
C18 Marine Engines Fuel Level - Test
Torque on the Impeller Bolt on Remanufactured Water Pumps{1361} Torque on the Impeller Bolt on Remanufactured Water Pumps{1361}
C3.3 and C4.4 Rental Generator Sets Starting the Engine
2007/05/21 An Update for Calibrating the Engine Oil Level Gauge {1326}
Inspection Procedures and Specifications for Pistons and Piston Pins {1214, 1214} Inspection Procedures and Specifications for Pistons and Piston Pins {1214, 1214}
C15 On-Highway Engine Diesel Particulate Filter
C13 Engine Valve Mechanism Cover Base - Remove and Install
C13 On-highway Engine Diesel Particulate Filter
C13 Engine Flywheel Housing - Remove and Install
CX28 On-Highway Transmission Transmission Control
CX28 On-Highway Transmission Speed Sensor (Transmission)
C13 Engine Engine Oil Pan - Remove and Install
C3.3 and C4.4 Rental Generator Sets Control Panel
C3.4 IND Industrial Engine Plate Locations and Film Locations
C18 Marine Engines Transmission Oil Pressure Is High
C18 Marine Engines Transmission Oil Temperature Is High
2007/04/23 100% Leak Testing of Oil Coolers {1378}
2007/04/30 100% Leak Testing of Oil Coolers {1378}
2007/05/01 100% Leak Testing of Oil Coolers {1378}
2007/07/16 Managing the Life Cycles of Excavator Final Drives {4050}
C13 Engine Flame Detection Temperature Sensor - Remove and Install
C13 and C15 On-highway Engines Test ECM Mode
3500C Marine Engines Engine Speed/Timing Sensor