Flame Detection Temperature Sensor - Remove and Install
Removal Procedure
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect harness assembly (1). Disconnect harness assembly (2) .
Show/hide table
Illustration 1 | g01372468 |
- Remove flame detection temperature sensor (3) .
Show/hide table
Illustration 2 | g01372473 |
- Remove flame detection temperature sensor (4) .
Show/hide table
Illustration 3 | g01372474 |
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 5P-3931     | Anti-Seize Compound     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Apply Tooling (A) to the threads of flame detection temperature sensor (4) .
Show/hide table
Illustration 4 | g01372474 |
- Install flame detection temperature sensor (4). Tightenflame detection sensor (4) to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
- Apply Tooling (A) to the threads of flame detection temperature sensor (3) .
Show/hide table
Illustration 5 | g01372473 |
- Install flame detection temperature sensor (3). Tighten flame detection temperature sensor (3) to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
- Connect harness assemblies (2) and (1) .
Show/hide table
Illustration 6 | g01372468 |
Caterpillar Information System:
2007/07/16 Managing the Life Cycles of Excavator Final Drives {4050}
2007/05/01 100% Leak Testing of Oil Coolers {1378}
2007/04/30 100% Leak Testing of Oil Coolers {1378}
2007/04/23 100% Leak Testing of Oil Coolers {1378}
C18 Marine Engines Transmission Oil Temperature Is High
C18 Marine Engines Transmission Oil Pressure Is High
C3.4 IND Industrial Engine Plate Locations and Film Locations
C3.3 and C4.4 Rental Generator Sets Control Panel
C13 Engine Engine Oil Pan - Remove and Install
C13 Engine Camshaft - Install
C13 Engine Camshaft - Remove
C18 Marine Engines Fuel Level - Test
C13 and C15 On-highway Engines Test ECM Mode
3500C Marine Engines Engine Speed/Timing Sensor
C3.4 IND Industrial Engine Emissions Certification Film
C18 Marine Engines Engine Top Speed Is Not Obtained
C15 On-Highway Engine Clean Gas Induction Temperature Sensor - Remove and Install
C13 Engine Air Pump (ARD Purge) - Remove
2007/04/30 An Improved Starting Motor is Now Available {1453}
Application and Instruction Guide for the Driveline PTO on CX28, CX31, and CX35 On-Highway Transmissions{1408, 3030, 3108} Application and Instruction Guide for the Driveline PTO on CX28, CX31, and CX35 On-Highway Transmissions{1408, 3030, 3108}
C13 Engine Air Pump (ARD Purge) - Install
C13 Engine Fuel Pressure Sensor - Remove and Install
C18 Marine Engines Sensor Signal (Analog, Active) - Test
C32 Marine Engine Plate Locations and Film Locations