Rollover Protective Structure (ROPS) - Remove and Install
- Disconnect harness assembly (1)
Show/hide table
Illustration 2 g03423864 Show/hide tableIllustration 3 g03427647 - Disconnect harness assembly (4). Loosen guard (2) to allow access to the ROPS bolts. Install a suitable lifting device to ROPS (5). The weight of the ROPS (5) is approximately
500 kg (1100 lb) . Remove bolts (3). Remove ROPS (5).
Show/hide table
Illustration 1 | g03423870 |
- Install ROPS (1) in the reverse order of installation.
- Install bolts (3). Tighten bolts (3) to a torque of
1800 ± 200 N·m (1350 ± 150 lb ft) .
- Install bolts (3). Tighten bolts (3) to a torque of
Caterpillar Information System:
PL83 and PL87 Pipelayers Machine Systems Piston Pump (Hydraulic Fan) - Assemble
PL83 and PL87 Pipelayers Machine Systems Piston Pump (Hydraulic Fan) - Disassemble
D10T2 Track-Type Tractor Engine Supplement Exhaust Cooler (NRS) - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Power Train Carrier Bearing (Drive Shaft) - Remove and Install
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Hood - Front
980H Wheel Loader Power Train Power Train Guard (Transmission) - Remove and Install
980H Wheel Loader Power Train Crankcase Guard - Remove and Install
D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader Power Train Gear Pump (Axle Oil Cooler) - Remove and Install
980H Wheel Loader Engine Supplement Engine Oil Pan - Remove and Install - In Chassis
901C, 902C and 903C Compact Wheel Loaders PowerTrain Differential (Limited Slip) - Remove
621K, 623K and 627K Wheel Tractor-Scrapers GPS Receiver Has Incorrect Indicators
Installation Procedure for the 422-3309 Valve Kit (High Flow) {5070} Installation Procedure for the 422-3309 Valve Kit (High Flow) {5070}
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Battery and Wiring Group
349F and 352F Excavators ECM - Replace
966H and 972H Wheel Loaders PowerTrain Oscillating Axle (Rear) - Remove and Install
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Drive Shaft (Center) - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train Sequence Valve - Test and Adjust
966H and 972H Wheel Loaders PowerTrain Fixed Axle (Front) - Remove and Install
980H Wheel Loader Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader C18 Engine Supplement Fuel Tank - Remove and Install
2013/08/26 New Software Is Now Used on Certain Medium Wheel Loaders {7610, 7620}
966H and 972H Wheel Loaders PowerTrain Heat Exchanger (Axle Oil Cooler) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Control Manifold (Axle Oil Flow Divider) - Remove and Install