ECM - Replace
在更换 ECM 之前,确保更换是必需要做的操作。 ECM 不太可能是故障的原因。 务必检查并确认 ECM 标有 "+ Battery(蓄电池正极)"的所有触点上有电。
注: 配置软件损坏或软件不正确可能会导致 ECM 报告错误的诊断代码。 更换 ECM 前,向 ECM 中闪存正确的配置软件,以确认故障与软件损坏无关。 请参阅故障诊断与排除, "ECM 软件 - 安装"。
步骤
- 将断路开关和钥匙起动开关转到断开位置。
- 从 ECM 上断开机器线束接头。
- 确认更换的 ECM 的零件号正确。
- 安装更换的ECM。
- 将机器线束与 ECM 相连。
- 将断路开关和钥匙起动开关转到接通位置。
- 如有必要,使用 Cat® 电子技师 (Cat ET) 维修工具安装配置软件。 请参阅本手册中的测试和调整, "ECM(Electronic Control Module,电子控制模块)- 闪存编程"一节。
- 确认 ECM 正常工作。
Caterpillar Information System:
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Battery and Wiring Group
Installation Procedure for the 422-3309 Valve Kit (High Flow) {5070} Installation Procedure for the 422-3309 Valve Kit (High Flow) {5070}
D9T Track-Type Tractor Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Piston Pump (Hydraulic Fan) - Assemble
PL83 and PL87 Pipelayers Machine Systems Piston Pump (Hydraulic Fan) - Disassemble
D10T2 Track-Type Tractor Engine Supplement Exhaust Cooler (NRS) - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Power Train Carrier Bearing (Drive Shaft) - Remove and Install
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Hood - Front
980H Wheel Loader Power Train Power Train Guard (Transmission) - Remove and Install
980H Wheel Loader Power Train Crankcase Guard - Remove and Install
D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader Power Train Gear Pump (Axle Oil Cooler) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Oscillating Axle (Rear) - Remove and Install
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Drive Shaft (Center) - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train Sequence Valve - Test and Adjust
966H and 972H Wheel Loaders PowerTrain Fixed Axle (Front) - Remove and Install
980H Wheel Loader Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader C18 Engine Supplement Fuel Tank - Remove and Install
2013/08/26 New Software Is Now Used on Certain Medium Wheel Loaders {7610, 7620}
966H and 972H Wheel Loaders PowerTrain Heat Exchanger (Axle Oil Cooler) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Control Manifold (Axle Oil Flow Divider) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Modulating Valve (Transmission Clutch) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Differential and Bevel Gear - Remove and Install
966H and 972H Wheel Loaders PowerTrain Service Brakes - Remove and Install