Engine Oil Pan - Remove and Install - In Chassis
Removal Procedure
Start By:
- Remove the crankcase guard.
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Refer to Operation and Maintenance Manual, "Engine Oil - Change". Refer to Operation and Maintenance Manual, "Engine Oil - Check" for the correct draining and filling procedure.
- Remove nut (2) and move the harness assembly out of the way. Remove stud bolts (3) .
Show/hide table
 | |
| Illustration 1 | g03423547 |
Bottom view of the machine. | |
- Remove bolts (1). Lower engine oil pan (4) as far as engine oil pan (4) will go.
- Remove bolt (5). Remove bolts (7). Remove tube assembly (6) and the O-ring seal from the engine. Lower tube assembly (6) into engine oil pan (4). Remove engine oil pan (4) .
Show/hide table
 | |
| Illustration 2 | g03423838 |
- Remove gasket (8). Discard gasket (8) .
Show/hide table
 | |
| Illustration 3 | g03423851 |
Installation Procedure
- Install engine oil pan (4) in the reverse order of removal.
- Install a new gasket (8) .
- Lubricate the O-ring seal for tube assembly (6) with the lubricant that is being sealed.
- Tighten nut (2) to a torque of 25 ± 6 N·m (221 ± 53 lb in).
Caterpillar Information System:
901C, 902C and 903C Compact Wheel Loaders PowerTrain Differential (Limited Slip) - Remove
621K, 623K and 627K Wheel Tractor-Scrapers GPS Receiver Has Incorrect Indicators
966M and 972M Wheel Loaders Automatic Lubrication System - If Equipped
966M and 972M Wheel Loaders Camera
312F and 313F Excavators Monitoring System
D10T2 Track-Type Tractor Engine Supplement Hydraulic Oil Cooler - Remove and Install
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Fixed Axle (Front) - Install
844K Wheel Dozer Operator Controls
D10T2 Track-Type Tractor Engine Supplement Fuel Cooler - Remove and Install
966M and 972M Wheel Loaders Quick Coupler Operation
D6T Track-Type Tractor Diesel Exhaust Fluid Filter - Replace
901C, 902C and 903C Compact Wheel Loaders PowerTrain Differential (Limited Slip) - Install
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader Power Train Gear Pump (Axle Oil Cooler) - Remove and Install
D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
980H Wheel Loader Power Train Crankcase Guard - Remove and Install
980H Wheel Loader Power Train Power Train Guard (Transmission) - Remove and Install
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Hood - Front
980M Tier 4 and 982M Tier 4 Wheel Loaders Power Train Carrier Bearing (Drive Shaft) - Remove and Install
D10T2 Track-Type Tractor Engine Supplement Exhaust Cooler (NRS) - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Piston Pump (Hydraulic Fan) - Disassemble
PL83 and PL87 Pipelayers Machine Systems Piston Pump (Hydraulic Fan) - Assemble
D9T Track-Type Tractor Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
Installation Procedure for the 422-3309 Valve Kit (High Flow) {5070} Installation Procedure for the 422-3309 Valve Kit (High Flow) {5070}
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Battery and Wiring Group