Engine Oil Line - Remove and Install
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 松开将机油管 (1) 上的夹子固定到喷油泵上的螺母 (2)。
- 拆下中空螺栓 (3)，然后从缸体上拆下垫圈 (4)。
Show/hide table
图 2 g01307372 典型示例 - 拆下中空螺栓 (5)，然后从缸盖上拆下垫圈 (6)。
- 从发动机上拆下机油管 (1)。
Show/hide table
| |
| 图 1 | g01304820 |
|
典型示例 | |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将机油管 (1) 放到发动机上。 确保机油管上的夹子位于螺母 (2) 下方。
- 将中空螺栓 (3) 和新的垫圈 (4) 置于机油管 (1) 上。 将中空螺栓和机油管安装到缸体上并用手拧紧。
Show/hide table
图 4 g01307372 典型示例 - 将中空螺栓 (5) 和新的垫圈 (6) 置于机油管 (1) 上。 将中空螺栓和机油管安装到缸盖上并用手拧紧。
- 拧紧将机油管 (1) 上的夹子固定到喷油泵上的螺母 (2)。
对于 C0.5、 C0.7、 C1.1 和 C1.6 发动机，将螺母 (2) 紧固至扭矩
6 N·m (53 lb in) 。对于 C1.5 和 C2.2 发动机，将螺母 (2) 紧固至扭矩
15 N·m (133 lb in) 。 - 拧紧中空螺栓 (3) 和 (5) 至扭矩为
12 N·m (106 lb in) 。
Show/hide table
|
| |
| 图 3 | g01304820 |
|
典型示例 | |
Caterpillar Information System:
C13 On-highway Engine Air Lines
G3520C and G3520E Generator Set Engines Turbocharger Turbine Temperature Is Low
G3520C and G3520E Generator Set Engines Oil Filter Differential Pressure Problem
G3520C and G3520E Generator Set Engines Engine Stalls Immediately After Starting
G3520C and G3520E Generator Set Engines Engine Shutdown Is Intermittent
G3520C and G3520E Generator Set Engines Engine Overloads
G3520C and G3520E Generator Set Engines Engine Misfires, Runs Rough or Is Unstable
G3520C and G3520E Generator Set Engines Engine Does Not Crank
G3520C and G3520E Generator Set Engines Engine Cranks but Does Not Start
G3600 Engines Symptom Troubleshooting
G3520C and G3520E Generator Set Engines Configuration Parameters
G3600 Engines Programmable Parameters
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 14 Amp and 15 Amp Alternators
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 40 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
C13 On-highway Engine Air Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Connecting Rod Bearings - Install - Connecting rods in position
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C0.5 and C0.7 Engines