Coolant Temperature Switch - Remove and Install - C0.5 and C0.7 Engines
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 有关更多资料，请参阅操作和保养手册, "冷却系统冷却液 - 排放"。
Show/hide table
图 1 g01325724 典型示例 - 从冷却液温度开关 (1) 上断开线束组件（未显示）。
- 从水泵 (2) 上拆下冷却液温度开关 (1)。
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 5P-3413 | 管密封胶 | 1 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查冷却液温度开关有无损坏以及是否工作正常。 有关更多资料，请参阅系统操作、测试和调整, "冷却液温度开关 - 测试"。 如有必要，更换冷却液温度开关。
Show/hide table
图 2 g01325724 典型示例 - 将冷却液温度开关 (1) 安装到水泵 (2) 上。 用深孔套筒将冷却液温度开关拧紧至扭矩
27 N·m (20 lb ft) 。注: 如果安装了一个旧的冷却液温度开关，将一薄层工具 (A) 涂敷在冷却液温度开关的螺纹上。
- 将线束组件（未显示）连接到冷却液温度开关 (1) 上。
- 向冷却系统加注冷却液到正确的液位。 有关更多资料，请参阅操作和保养手册, "冷却系统冷却液 - 加注"。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Connecting Rod Bearings - Install - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C13 On-highway Engine Air Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 40 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 14 Amp and 15 Amp Alternators
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Line - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C1.1, C1.5, C1.6 and C2.2 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Turbocharged Engines
G3520C and G3520E Generator Set Engines Turbocharger Compressor Bypass - Test
G3520C and G3520E Generator Set Engines Detonation - Test
C11 and C13 Engines and 14M and 16M Motor Graders CAN Data Link - Test
G3520C and G3520E Generator Set Engines Electrical Power Supply - Test
C9 Engines for Motor Graders Fuel Filter Differential Pressure - Test
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Filter Is Restricted
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290} Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
C13 On-highway Engine Air Lines
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Transfer Pump - Test