Camshaft - Assemble
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保凸轮轴组件的所有部件清洁无损坏。
Show/hide table
图 1 g01326129 典型示例 - 用清洁的发动机机油润滑凸轮轴 (1) 的鼻端。 使用合适的压具将轴承 (3) 安装到凸轮轴上。
注: 确保将轴承安装在正确方位。 应将凸轮轴轴承垂直压到凸轮轴上，否则可能会损坏轴承。 切勿按压轴承的外座圈。
- 将垫片 (4) 和月牙键 (2) 安装到凸轮轴 (1) 上。
- 对准齿轮 (5) 和月牙键 (2)。 使用合适的压具将齿轮安装到凸轮轴 (1) 的鼻端。
注: 应将齿轮放在一个合适的支架上，以防止在安装过程中损坏调速器飞锤。
结束:
- 安装凸轮轴组件。 请参阅拆解和组装, "凸轮轴 - 安装"。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C13 On-highway Engine Air Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 40 Amp Alternator
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 14 Amp and 15 Amp Alternators
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Line - Remove and Install
C13 On-highway Engine Air Lines
G3520C and G3520E Generator Set Engines Turbocharger Turbine Temperature Is Low
G3520C and G3520E Generator Set Engines Oil Filter Differential Pressure Problem
G3520C and G3520E Generator Set Engines Engine Stalls Immediately After Starting
G3520C and G3520E Generator Set Engines Engine Shutdown Is Intermittent
G3520C and G3520E Generator Set Engines Engine Overloads
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Camshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Connecting Rod Bearings - Install - Connecting rods in position
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C0.5 and C0.7 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Coolant Temperature Switch - Remove and Install - C1.1, C1.5, C1.6 and C2.2 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Turbocharged Engines
G3520C and G3520E Generator Set Engines Turbocharger Compressor Bypass - Test
G3520C and G3520E Generator Set Engines Detonation - Test
C11 and C13 Engines and 14M and 16M Motor Graders CAN Data Link - Test