Customer Parameters Worksheet
Record the following information before you change any programmable parameter.
Show/hide table
Equipment ID     |     |
Engine Serial Number     |     |
Serial number for Electronic Control Module (ECM)     |     |
"Full load setting (FLS)"     |     |
"Full torque setting (FTS)"     |     |
Fuel Ratio Control (FRC) Offset     |     |
Rated Fuel Position     |     |
Low Idle Speed     |     |
High Idle Speed     |     |
Fuel Correction Factor     |     |
Engine Cooling System     |     |
Identifier for Cat Data Link     |     |
Cold Mode Cylinder Cutout     |     |
Cooldown Speed     |     |
Engine Cooldown Duration     |     |
Engine Acceleration Rate     |     |
Intermediate Speed     |     |
Engine Prelube Duration     |     |
Crank Duration     |     |
Maximum Number Of Crank Cycles     |     |
Crank Terminate Speed     |     |
Air Shutoff     |     |
Air Inlet Shutoff Detection     |     |
Cooling Warning Engine Load Enable     |     |
Ether Control     |     |
Injector Trim Code
Show/hide table
Injector Trim Code     | |
---|---|
Injector     | Trim Code     |
"Inj #1 e-trim"     |     |
"Inj #2 e-trim"     |     |
"Inj #3 e-trim"     |     |
"Inj #4 e-trim"     |     |
"Inj #5 e-trim"     |     |
"Inj #6 e-trim"     |     |
"Inj #7 e-trim"     |     |
"Inj #8 e-trim"     |     |
"Inj #9 e-trim"     |     |
"Inj #10 e-trim"     |     |
"Inj #11 e-trim"     |     |
"Inj #12 e-trim"     |     |
"Inj #13 e-trim"     |     |
"Inj #14 e-trim"     |     |
"Inj #15 e-trim"     |     |
"Inj #16 e-trim"     |     |
Record the following information from the engine monitoring system. The engine monitoring system can be accessed through the Caterpillar Electronic Technician (ET). Select "Monitoring System" from the "Service" menu.
Low System Voltage
Show/hide table
Warning Trip Points     |     |
Warning Delay Time     |     |
Low Engine Oil Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
High Coolant Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
Low Coolant Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Engine Overspeed
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
High Air Filter Restriction Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Altitude (Atmospheric Pressure)
Show/hide table
Derate Trip Point     |     |
High Exhaust Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
High Engine Oil Filter Restriction Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
High Fuel Filter Restriction Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
High Crankcase Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
High Aftercooler Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
Caterpillar Information System:
CX38-P892 Well Servicing Transmission Operational Checks
C9 Industrial Engines Fuel System
C175 Generator Sets Driven Equipment - Check
3500B Industrial Engines with the ADEM 3 Electronic Control Module System Configuration Parameters
C9 Industrial Engines General Information
BA-921 Bendix Air Compressor Unloader Piston - Remove
BA-921 Bendix Air Compressor Unloader Piston - Install
2006/06/12 Improved Elbows are Used for Inlet Air {1071}
CX31-P600 Petroleum Transmission Speed Sensor (Transmission)
3500B Industrial Engines with the ADEM 3 Electronic Control Module Event Code List
SR5 Electric Power Generation Bearing - Remove and Install
SR5 Electric Power Generation Coupling - Install
CX31-P600 Petroleum Transmission Transmission Hydraulic Control
3512B Oil Well Servicing Engines Fuel Priming Pump
G3408C and G3412C Engines Engine Valve Lash - Inspect/Adjust
C4.4 Industrial Engine Air Inlet and Exhaust System
C4.4 Industrial Engine Camshaft
2006/05/15 An Improved Jacket Water Pump is Used by Certain G3500B, G3500C, and G3500E Engines {1361}
C7 On-Highway Engine Engine Oil Pump - Remove
C7 On-Highway Engine Engine Oil Pump - Install
2009/10/29 Inspection and/or Repair Procedure to Replace Crankshafts on Truck Engines {1202}
G3406 Engine Ignition Systems
2006/05/01 Inspection and/or Repair Procedure to Replace Crankshafts on Industrial Engines {1202}
C11 and C13 Engines Piston and Rings