Speed Sensor (Transmission)
每个转速传感器有两个连接至 ECM(+ 和 −)的接头。 对于所有转速传感器,接头触点 "2" 是信号线,接头触点 "1" 是回路线。 转速传感器向 ECM 发送与每秒钟经过传感器的轮齿数匹配的 AC 频率信号 (HZ)。 ECM 比较转速传感器的频率 (HZ) 与每转脉冲数,以便确定旋转部件的转速。 ECM 利用来自转速传感器的输入调整变速箱档位。
转速传感器用于正常操作期间的交叉检查和彼此诊断。 交叉检查使用两个变速箱输出转速和变矩器输出转速来验证并确定用于换档的变速箱输出转速传感器。 交叉检查比较三个转速。 如果至少两个转速一致,则变速箱会按预期换档。 否则将禁止换档,且锁定离合器将分离。ECM 定期检查转速传感器的值,如果发现错误、异常或缺失的值,ECM 将会记录一个维修代码(转速传感器诊断),指示转速传感器电路存在故障。
Show/hide table
图 1 | g02017533 |
(左视图和后视图)
(1) 发动机输出转速传感器 (2) 变矩器输出转速传感器 (3) 变速箱输出转速传感器 |
直通变速箱上有一个发动机输出转速传感器 (1),一个变矩器输出转速传感器 (2) 和两个变速箱输出转速传感器 (3)。 所有转速传感器均用于确定任何单独的转速传感器是否存在故障。
升降箱变速箱上有一个发动机输出转速传感器 (1),一个变矩器输出转速传感器 (2),一个变速箱输出转速传感器 (3),一个工作模式输出转速传感器 (4),一个后轮驱动断开转速传感器 (5) 和一个前轮驱动断开转速传感器 (6)。 工作模式期间,变速箱输出转速传感器 (3) 和工作模式输出转速传感器 (4) 激活,并用于交叉检查变速箱输出转速和彼此诊断。 行驶模式期间,变速箱输出转速传感器 (3) 和后轮驱动断开转速传感器 (5) 激活,并用于交叉检查变速箱输出转速和彼此诊断。 在与变速箱输出转速传感器 (3) 的转速进行比较前,会对后轮驱动断开转速传感器 (5) 和前轮驱动断开转速传感器 (6) 的转速进行调整,以消除由于升降箱啮合带来的转速变化效应。 "4WD" 升降箱变速箱上配备的前轮驱动断开转速传感器 (6) 仅供参考使用。
Show/hide table
图 2 | g02017633 |
(3) 变速箱输出转速传感器
(4) 工作模式输出转速传感器 |
Show/hide table
图 3 | g02017813 |
(5) 后轮驱动断开转速传感器 |
Show/hide table
图 4 | g02056479 |
4WD 升降箱 (6) 前轮驱动断开转速传感器 |
Caterpillar Information System:
3500B Industrial Engines with the ADEM 3 Electronic Control Module Event Code List
SR5 Electric Power Generation Bearing - Remove and Install
SR5 Electric Power Generation Coupling - Install
SR5 Electric Power Generation Coupling - Remove
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies AC Output Current - Calibrate
SR5 Electric Power Generation Generator - Align
SR5 Electric Power Generation Generator - Install
SR5 Electric Power Generation Generator - Remove
C7 On-Highway Engine Camshaft Idler Gear - Remove and Install
SR5 Electric Power Generation Rotor - Remove and Install
C7 On-Highway Engine Housing (Front) - Install
C175-16 and C175-20 Generator Set Engines Fuel Transfer Pump
2006/06/12 Improved Elbows are Used for Inlet Air {1071}
BA-921 Bendix Air Compressor Unloader Piston - Install
BA-921 Bendix Air Compressor Unloader Piston - Remove
C9 Industrial Engines General Information
3500B Industrial Engines with the ADEM 3 Electronic Control Module System Configuration Parameters
C175 Generator Sets Driven Equipment - Check
C9 Industrial Engines Fuel System
CX38-P892 Well Servicing Transmission Operational Checks
3500B Industrial Engines with the ADEM 3 Electronic Control Module Customer Parameters Worksheet
CX31-P600 Petroleum Transmission Transmission Hydraulic Control
3512B Oil Well Servicing Engines Fuel Priming Pump
G3408C and G3412C Engines Engine Valve Lash - Inspect/Adjust