Tilt Lever - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
C | 316-1752 | Pin Positioner | 1 |
E | 318-2119 | Installation Plate | 1 |
318-2118 | Installation Plate | 1 | |
318-2117 | Installation Plate | 1 | |
146-1799 | Hard Washer | 1 | |
289-0008 | Puller Stud | 1 | |
7H-7539 | Full Nut | 1 | |
6V-0113 | Double Acting Cylinder | 1 | |
F | 318-2118 | Installation Plate | 1 |
318-2117 | Installation Plate | 1 | |
318-2120 | Plate | 1 | |
9U-6698 | Stud Puller | 1 | |
8H-3390 | Full Nut | 1 | |
3S-6162 | Hard Washer | 1 | |
6V-0014 | Hydraulic Cylinder Gp | 1 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Attach a suitable lifting device to tilt lever (9). The weight of tilt lever (9) is approximately
1501 kg (3310 lb) . Position tilt lever (9).Show/hide tableIllustration 2 g01521282 - Install Tooling (F) in order to install pin (14). Install pin (10).
Show/hide table
Illustration 3 g01521842 - Install collet (13). Install plugs (12). Repeat for the opposite side.
- Install bolt (11).
Show/hide table
Illustration 4 g01521270 Show/hide tableIllustration 5 g01521280 - Attach Tooling (C) and a suitable lifting device to pin (3). Remove pin (3) and the collets. Extend tilt cylinder (4).
- Install Tooling (E) in order to install pin (3). Install pin (3).
Show/hide table
Illustration 6 g01521840 - Install collet (2). Repeat for the opposite side.
- Install bolt (1).
Show/hide table
Illustration 7 g01521275 Show/hide tableIllustration 8 g01521281 - Attach a suitable lifting device to tilt link (8). The weight of tilt link (8) is approximately
246 kg (542 lb) . Install Tooling (E) in order to install pin (10). Install pin (10).Show/hide tableIllustration 9 g01521844 - Install collet (7). Install plugs (6). Repeat for the opposite side.
- Install bolt (5).
Show/hide table
Illustration 1 | g01521274 |
Caterpillar Information System:
993K Wheel Loader Machine Systems Control Manifold (Operator Lift) (Main) - Install
993K Wheel Loader Machine Systems Hydraulic Tank (Operator Lift) - Install
613G Wheel Tractor-Scraper Hydraulic System Machine Preparation for Troubleshooting
584 and 584HD Forwarders Camera - If Equipped
2008/08/25 Improvements Have Been Made to the Fuel Level Sensor Group {1273, 7481}
993K Wheel Loader Machine Systems Cab Blower (Air Conditioner, Heater Fan) - Install
993K Wheel Loader Machine Systems Access Platform (Operator Lift) - Install
993K Wheel Loader Machine Systems Ride Control Valve - Install
2008/10/27 A New U-Cup Seal Updates the Servo Steering Cylinder {4315}
613G Wheel Tractor-Scraper Power Train Torque Converter Inlet Oil Pressure - Test
2008/08/25 Improved Lower Pin Joint for Bucket {6107, 6108, 6109, 6118}
Installation Procedure For The New Duct Assembly{1405} Installation Procedure For The New Duct Assembly{1405}
993K Wheel Loader Machine Systems Piston Pump (Implement Pilot) (Axle Oil Cooler) - Install
613G Wheel Tractor-Scraper Machine Systems General Information
993K Wheel Loader Machine Systems Main Control Valve (LH) - Install
993K Wheel Loader Machine Systems Hydraulic Tank (Implement, Hydraulic Fan) - Install
Filtration Procedure Wheel Tractor Scraper Transmission Oil {0680, 0768, 3016, 3030} Filtration Procedure Wheel Tractor Scraper Transmission Oil {0680, 0768, 3016, 3030}
966H and 972H Wheel Loaders Mirror - If Equipped
993K Wheel Loader Machine Systems Hydraulic Tank (Steering) (Brake) - Install
2008/09/29 A New Torque Converter Group Is Used {3101}
993K Wheel Loader Machine Systems Piston Pump (Implement) - Install - Front and Rear, RH
993K Wheel Loader Machine Systems Hydraulic Tank (Implement, Hydraulic Fan) - Assemble
993K Wheel Loader Power Train Axle Oil Cooler (Front) - Install
993K Wheel Loader Engine Supplement Engine Oil Cooler - Install