Access Platform (Operator Lift) - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 2 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Attach Tooling (A) and a suitable lifting device to access platform (3). The weight of access platform (3) is approximately
710 kg (1560 lb) .Show/hide table
Illustration 2 g01527439 - Position the access platform. Install bolts (10). Connect hose assemblies (9).
Show/hide table
Illustration 3 g01527438 - Install bolts (8).
Show/hide table
Illustration 4 g01527437 - Install bracket (7). Repeat for opposite side.
Show/hide table
Illustration 5 g01522932 - Install bolts (6).
Show/hide table
Illustration 6 g01522931 - Connect harness assembly (5).
Show/hide table
Illustration 7 g01522930 - Install panel (4).
Show/hide table
Illustration 8 g01522928 - Install Tooling (A). Install bracket (2). Connect harness assembly (1).
Show/hide table
| |
| Illustration 1 | g01522929 |
Caterpillar Information System:
993K Wheel Loader Machine Systems Ride Control Valve - Install
2008/10/27 A New U-Cup Seal Updates the Servo Steering Cylinder {4315}
613G Wheel Tractor-Scraper Power Train Torque Converter Inlet Oil Pressure - Test
2008/08/25 Improved Lower Pin Joint for Bucket {6107, 6108, 6109, 6118}
Installation Procedure For The New Duct Assembly{1405} Installation Procedure For The New Duct Assembly{1405}
C9.3 Engine for D7E Track-Type Tractor Electronic Control System Components
C9.3 Engine for D7E Track-Type Tractor General Information
Procedure to Rework Housings for the Installation of New Planetary Bolts{3030, 3064, 3105} Procedure to Rework Housings for the Installation of New Planetary Bolts{3030, 3064, 3105}
D3K, D4K and D5K Track-Type Tractors Caterpillar Approved Work Tools
D6K Track-Type Tractor Operator Controls
C4.4 Engines For Caterpillar Built Machines Engine Cranks but Will Not Start
993K Wheel Loader Machine Systems Piston Pump (Implement) - Remove - Front and Rear, RH
993K Wheel Loader Machine Systems Cab Blower (Air Conditioner, Heater Fan) - Install
2008/08/25 Improvements Have Been Made to the Fuel Level Sensor Group {1273, 7481}
584 and 584HD Forwarders Camera - If Equipped
613G Wheel Tractor-Scraper Hydraulic System Machine Preparation for Troubleshooting
993K Wheel Loader Machine Systems Hydraulic Tank (Operator Lift) - Install
993K Wheel Loader Machine Systems Control Manifold (Operator Lift) (Main) - Install
993K Wheel Loader Machine Systems Tilt Lever - Install
993K Wheel Loader Machine Systems Piston Pump (Implement Pilot) (Axle Oil Cooler) - Install
613G Wheel Tractor-Scraper Machine Systems General Information
993K Wheel Loader Machine Systems Main Control Valve (LH) - Install
993K Wheel Loader Machine Systems Hydraulic Tank (Implement, Hydraulic Fan) - Install
Filtration Procedure Wheel Tractor Scraper Transmission Oil {0680, 0768, 3016, 3030} Filtration Procedure Wheel Tractor Scraper Transmission Oil {0680, 0768, 3016, 3030}