Piston Pump (Implement) - Install - Front and Rear, RH
- Position O-ring (20) and connect front piston pump (18) to rear piston pump (21).
- Install bolts (19).
- Position O-ring (22) onto rear piston pump (21).
Show/hide table
Illustration 2 g01624958 - Attach a suitable lifting device to piston pump assembly (17). The weight of piston pump assembly (17) is approximately
25 kg (550 lb) . - Position piston pump assembly (17) and install bolts (16).
Show/hide table
Illustration 3 g01624379 - Connect hose assemblies (13), (14), and (15).
- Connect harness assemblies (12) to the two coil assemblies (not shown).
Show/hide table
Illustration 4 g01624370 - Connect hose assemblies (9), (10), and (11).
- Install the rear drive shaft, if necessary. Refer to Disassembly and Assembly , "Drive Shaft (Rear) - Install".
- Install the auxiliary drive shaft, if necessary. Refer to Disassembly and Assembly , "Drive Shaft (Auxilliary) - Remove and Install".
Show/hide table
Illustration 5 g01624169 - Install bracket assembly (6).
- Position tube assembly (8) and install clamp assemblies (5).
- Install clamp assemblies (7).
Show/hide table
Illustration 6 g01457199 Show/hide tableIllustration 7 g01457197 - Remove pin (4) and lower platform (3).
- Install bolt (2).
Show/hide table
Illustration 8 g01625590 - Open the access doors that are located behind the cab. Rotate shut off valves (1) for the suction lines that are located on the bottom of the hydraulic oil tank 90 degrees into the open position, as shown.
Show/hide table
Illustration 1 | g01625253 |
Caterpillar Information System:
2008/09/29 A New Torque Converter Group Is Used {3101}
993K Wheel Loader Machine Systems Hydraulic Tank (Steering) (Brake) - Install
966H and 972H Wheel Loaders Mirror - If Equipped
Filtration Procedure Wheel Tractor Scraper Transmission Oil {0680, 0768, 3016, 3030} Filtration Procedure Wheel Tractor Scraper Transmission Oil {0680, 0768, 3016, 3030}
993K Wheel Loader Machine Systems Hydraulic Tank (Implement, Hydraulic Fan) - Install
993K Wheel Loader Machine Systems Main Control Valve (LH) - Install
613G Wheel Tractor-Scraper Machine Systems General Information
993K Wheel Loader Machine Systems Piston Pump (Implement Pilot) (Axle Oil Cooler) - Install
993K Wheel Loader Machine Systems Tilt Lever - Install
993K Wheel Loader Machine Systems Control Manifold (Operator Lift) (Main) - Install
993K Wheel Loader Machine Systems Hydraulic Tank (Operator Lift) - Install
613G Wheel Tractor-Scraper Hydraulic System Machine Preparation for Troubleshooting
993K Wheel Loader Machine Systems Hydraulic Tank (Implement, Hydraulic Fan) - Assemble
993K Wheel Loader Power Train Axle Oil Cooler (Front) - Install
993K Wheel Loader Engine Supplement Engine Oil Cooler - Install
993K Wheel Loader Power Train Tire and Rim (Front) - Remove and Install
993K Wheel Loader Engine Supplement Makeup Valve (Hydraulic Fan Motor) - Assemble
IT38H Integrated Toolcarrier and 938H Wheel Loader Camera - Rear View Camera (If Equipped)
966H and 972H Wheel Loaders Camera
966H and 972H Wheel Loaders Restricted Visibility
Bench Test Procedure for a 651E, 657E, and 657G Tractor Transmissions{3030, 3073} Bench Test Procedure for a 651E, 657E, and 657G Tractor Transmissions{3030, 3073}
D3K, D4K and D5K Track-Type Tractors Fuel System Water Separator - Replace
993K Wheel Loader Power Train Torque Converter - Install
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves