Hydraulic Accumulator (Boom, Hook) - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-8792 | Chain Wrench | 2 |
C | 335-3395 | Wrench | 1 |
- Install O-ring seal (12) onto end cap (7).
Show/hide table
Illustration 2 g01622136 - Install O-ring seals (11) and O-ring seal (10) onto piston (9).
- Install piston (9) into the hydraulic accumulator (boom, hook).
- Install O-ring seal (8) onto end cap (5).
Show/hide table
Illustration 3 g01622193 - Use Tooling (A) and a suitable holding device to secure hydraulic accumulator (boom, hook) (1). Use Tooling (C) to install end cap (7). Tighten end cap (7) to a torque of
122 ± 6 N·m (90 ± 4 lb ft) .Show/hide tableIllustration 4 g01622119 - Install fitting (6) onto hydraulic accumulator (boom, hook) (1).
Show/hide table
Illustration 5 g01622200 - Use Tooling (A) and a suitable holding device to secure hydraulic accumulator (boom, hook) (1). Use Tooling (C) to install end cap (5). Tighten end cap (5) to a torque of
122 ± 6 N·m (90 ± 4 lb ft) .Show/hide tableIllustration 6 g01622071 - Install the O-ring seal and accumulator charging valve (4). Tighten accumulator charging valve (4) to a torque of
35 ± 2 N·m (26 ± 1 lb ft) . - If necessary, tighten the cap for accumulator charging valve (4) to a torque of
1.6 ± 0.1 N·m (14 ± 0.9 lb in) . - Position gas valve protector (3) on hydraulic accumulator (boom, hook) (1) and install bolts (2).
- Charge the hydraulic accumulator (boom, hook). Refer to Testing and Adjusting, "Accumulator (Dead Engine Lower) - Test and Charge" for the correct charging procedure.
Show/hide table
Illustration 1 | g01622158 |
End By:
- Install the hydraulic accumulator (boom, hook).
Caterpillar Information System:
2008/10/06 Improvement for Hose Routing of 994 Wheel Loader Dual Tilt Hose Kickout {5057, 5104}
Procedure For Configuring The Implement Valve Solenoid{5264, 5479} Procedure For Configuring The Implement Valve Solenoid{5264, 5479}
613G Wheel Tractor-Scraper Machine Systems Floor
613G Wheel Tractor-Scraper Steering System Relief Valve (Steering) - Test and Adjust
Electronic Technician Failure While Calibrating{0785, 7569} Electronic Technician Failure While Calibrating{0785, 7569}
PL61 Pipelayer Machine Systems Hydraulic Accumulator (Boom, Hook) - Disassemble
2008/08/11 Missing Backflow Check Valve {5068}
2008/08/11 New C18 Cylinder Liners and O-ring Seals are Used {1201, 1216, 1216}
613G Wheel Tractor-Scraper Steering System Pump Control Valve (Secondary Steering) - Test and Adjust
2008/09/29 A New Pilot Valve for the Elevator is Now Available on Certain Wheel Tractor-Scrapers {5059, 5304}
Installation of the 318-8496 Engine Kit (Power Optimization) for the 980H Wheel Loader{1000} Installation of the 318-8496 Engine Kit (Power Optimization) for the 980H Wheel Loader{1000}
D11T Track-Type Tractor Ladder System
3408E and 3412E Engines for Caterpillar Built Machines Fuel Temperature Sensor
E194 Event Codes Falsely Alert the Driver by Illuminating the Diagnostic Lamp on Wheel Tractor Scrapers{1901, 7620} E194 Event Codes Falsely Alert the Driver by Illuminating the Diagnostic Lamp on Wheel Tractor Scrapers{1901, 7620}
613G Wheel Tractor-Scraper System Pressure Release
2008/08/11 A New PIN Plate Is Being Installed {7000, 7557}
994F Wheel Loader Camera - Video Camera (If Equipped)
320D Excavator Camera
D6K Track-Type Tractor Mirror - If Equipped
2008/08/18 Installation Of Software On A Replacement ECM {7610, 7620}
3408E and 3412E Engines for Caterpillar Built Machines Electrical Connectors - Inspect
906H, 906H2, 907H, 907H2, 908H and 908H2 Compact Wheel Loaders Monitoring System Monitoring System
2008/08/11 Improvements to the Bezel of the Dashboard {7451}
2008/12/01 Improvements To Brake Hose Assemblies Across Hitch {4257, 4269}