Clean Gas Induction Valve - Assemble
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many internal parts are not available for this component. Care must be taken during disassembly and assembly in order to prevent damage to unavailable parts.
- Install sensor (23). Install fitting (22). Install plug (21). Install O-ring seal (20) .
Show/hide table
 | |
| Illustration 1 | g01301947 |
- Position flange (19) onto clean gas induction valve (5). Install bolts (18) .
Show/hide table
 | |
| Illustration 2 | g01301946 |
- Install O-ring seals (17) .
Show/hide table
 | |
| Illustration 3 | g01301941 |
- If wiper (16) and the cushion are worn or damaged replace the clean gas induction valve. Install O-ring seal (15) .
Show/hide table
 | |
| Illustration 4 | g01301940 |
- Install O-ring seal (14). Install O-ring seals (13) .
Show/hide table
 | |
| Illustration 5 | g01257796 |
- Install harness assembly (12) onto coil assembly (11). Install coil assembly (11) onto solenoid valve (8). Install nut (10) .
Show/hide table
 | |
| Illustration 6 | g01258120 |
Show/hide table
 | |
| Illustration 7 | g01257771 |
- Install cover assembly (10). Install bolts (9). Install solenoid valve (8). Install fitting (7). Install fitting (6) .
Show/hide table
 | |
| Illustration 8 | g01257750 |
- Position flange (4) onto clean gas induction valve (5). Install bolts (3) .
Show/hide table
 | |
| Illustration 9 | g01257942 |
- Position actuator assembly (2) onto clean gas induction valve (5). Install bolts (1) .
End By: Install the clean gas induction valve. Refer to Disassembly and Assembly, "Clean Gas Induction Valve - Install".
Caterpillar Information System:
C15 On-Highway Engine Clean Gas Induction Valve - Disassemble
C280 Marine Propulsion Engines User Defined Shutdown Input
G3508, G3512 and G3516 Engines Electronic Control Module - Remove and Install
C7 On-Highway Engine Turbocharger - Remove
C7 PETROLEUM Petroleum Engine Engine Oil Filter Base - Install
C7 On-highway Engine Fuel Filter Base
C7 PETROLEUM Petroleum Engine Engine Oil Filter Base - Assemble
G3500 A3 Engines Engine Governing - Adjust
2006/03/27 Sealing and Installing the Flywheel Housing {1157, 7555}
C7 On-Highway Engine Clean Gas Induction Valve - Remove
C7 PETROLEUM Petroleum Engine Engine Oil Filter Base - Disassemble
C15 Industrial Engine Powertrain Data Link Circuit - Test
C7 On-highway Engine Crankshaft Pulley
G3500 A3 Engines Oxygen Sensor - Calibrate
G3500 A3 Engines Measuring Exhaust Temperature
C7 PETROLEUM Petroleum Engine Water Pump - Remove
G3500 A3 Engines Measuring Engine Oil Pressure
C7 On-highway Engine Air Inlet Elbow
Installing Injectors on the 3116, 3116T, and 3126 Industrial Engines{1290} Installing Injectors on the 3116, 3116T, and 3126 Industrial Engines{1290}
C7 On-highway Engine Air Inlet Elbow
C7 On-highway Engine Air Inlet Elbow
C7 PETROLEUM Petroleum Engine Water Pump - Disassemble
3512B Petroleum Engine Product Storage
C7 PETROLEUM Petroleum Engine Water Pump - Assemble