Clean Gas Induction Valve - Disassemble
Disassembly Procedure
Start By:
- Remove the clean gas induction valve. Refer to Disassembly and Assembly, "Clean Gas Induction Valve - Remove".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many internal parts are not available for this component. Care must be taken during disassembly and assembly in order to prevent damage to unavailable parts.
- Remove bolts (1) in order to remove actuator assembly (2) from clean gas induction valve (5) .
Show/hide table
 | |
| Illustration 1 | g01257942 |
- Remove bolts (3) in order to remove flange (4) from clean gas induction valve (5) .
- Remove fitting (6). Remove fitting (7). Remove solenoid valve (8). Remove bolts (9). Remove cover assembly (10) .
Show/hide table
 | |
| Illustration 2 | g01257750 |
- Remove nut (10) in order to remove coil assembly (11) from solenoid valve (8). Remove harness assembly (12) .
Show/hide table
 | |
| Illustration 3 | g01257771 |
Show/hide table
 | |
| Illustration 4 | g01258120 |
- Remove O-ring seals (13). Remove O-ring seal (14) .
Show/hide table
 | |
| Illustration 5 | g01257796 |
- Remove O-ring seal (15). Check wiper (16) and the cushion for wear or for damage.
Show/hide table
 | |
| Illustration 6 | g01301940 |
- Remove O-ring seals (17) .
Show/hide table
 | |
| Illustration 7 | g01301941 |
- Remove bolts (18) in order to remove flange (19) from clean gas induction valve (5) .
Show/hide table
 | |
| Illustration 8 | g01301946 |
- Remove O-ring seal (20). Remove plug (21). Remove fitting (22). Remove sensor (23) .
Show/hide table
 | |
| Illustration 9 | g01301947 |
Caterpillar Information System:
C280 Marine Propulsion Engines User Defined Shutdown Input
G3508, G3512 and G3516 Engines Electronic Control Module - Remove and Install
C7 On-Highway Engine Turbocharger - Remove
C7 PETROLEUM Petroleum Engine Engine Oil Filter Base - Install
C7 On-highway Engine Fuel Filter Base
C7 PETROLEUM Petroleum Engine Engine Oil Filter Base - Assemble
G3500 A3 Engines Engine Governing - Adjust
2006/03/27 Sealing and Installing the Flywheel Housing {1157, 7555}
C7 On-Highway Engine Clean Gas Induction Valve - Remove
C7 PETROLEUM Petroleum Engine Engine Oil Filter Base - Disassemble
C15 Industrial Engine Powertrain Data Link Circuit - Test
AccuGrade® GPS (CD700) Sensor Firmware Upgrade
C15 On-Highway Engine Clean Gas Induction Valve - Assemble
C7 On-highway Engine Crankshaft Pulley
G3500 A3 Engines Oxygen Sensor - Calibrate
G3500 A3 Engines Measuring Exhaust Temperature
C7 PETROLEUM Petroleum Engine Water Pump - Remove
G3500 A3 Engines Measuring Engine Oil Pressure
C7 On-highway Engine Air Inlet Elbow
Installing Injectors on the 3116, 3116T, and 3126 Industrial Engines{1290} Installing Injectors on the 3116, 3116T, and 3126 Industrial Engines{1290}
C7 On-highway Engine Air Inlet Elbow
C7 On-highway Engine Air Inlet Elbow
C7 PETROLEUM Petroleum Engine Water Pump - Disassemble
3512B Petroleum Engine Product Storage