Crankcase Breather - Remove and Install - Turbocharged Engines
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 拆下螺栓 (1),然后拆下盖 (2)、弹簧 (3) 和膜片 (4) 的组件。 记下盖 (2) 的方位。
- 从盖 (2) 上拆下弹簧 (3) 和膜片 (4)。
- 将适配器 (5) 和接头 (6) 从气门机构盖 (7) 上拆下。
注: 作临时标记以指示适配器的方位,方便安装。
- 如有必要,遵循步骤 4.a 至 4.c 以便拆下呼吸器的滤网。
- 拆下气门机构盖 (7)。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
- 拆下螺钉 (9),然后小心地拆下板 (10)。
- 从气门机构盖 (7) 上拆下滤网 (8)。
Show/hide table
图 1 | g01310618 |
典型示例 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | Loctite 594 | |
B | 247-5377 | 扭矩扳手 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
确保呼吸器总成零部件正确安装。如果呼吸器总成不能正常工作,发动机可能发生损坏。 |
- 清洁并检查所有零件。 更换任何损坏或磨损的零件。 确保气门机构盖中的呼吸器凹槽清洁。 确保适配器 (5) 上的通风孔和盖 (2) 上的通风孔未堵塞。
- 如有必要,遵循步骤 2.a 至 2.e,以便安装呼吸器的滤网。
- 将滤网 (8) 安装到气门机构盖 (7) 上。
- 将一滴工具 (A) 涂抹到气门机构盖 (7) 上的板配合面上。
- 将板 (10) 放置在气门机构盖 (7) 上,安装螺钉 (9)。
- 拧紧螺钉 (9) 至扭矩为
1.5 N·m (13 lb in) 。 - 安装气门机构盖 (7)。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
- 将新接头 (6) 放到气门机构盖上并安装适配器 (5)。
注: 确保适配器的方位正确。 通风孔应朝上。
Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 将膜片 (4) 和弹簧 (3) 安装到盖 (2) 上。
- 将盖 (2)、弹簧 (3) 和膜片 (4) 的组件放置在气门机构盖 (7) 上。
注: 确保盖的方位正确。
- 安装螺栓 (1)。 使用工具 (B) 拧紧螺栓至扭矩
3 N·m (27 lb in) 。
Show/hide table
图 2 | g01310618 |
典型示例 |
Caterpillar Information System:
D6K Track-Type Tractor Machine Systems Bottom Guard - Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Scavenge Pump and Mounting (Flywheel) - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004} Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Mounting and Dismounting
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
D6K Track-Type Tractor Machine Systems Bottom Guard - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System System Schematic
C-9 Engine for D6R Series II Track-Type Tractor CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050} Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Drive Shaft - Remove
C11 and C13 Engines and 14M and 16M Motor Graders CAN Data Link - Test
2006/09/18 A New Alternator Support and a New Belt are Used {1397, 1405}
D6G Series II Track-Type Tractor Machine Systems Bulldozer Brace - Remove and Install
D6K Track-Type Tractor Electrohydraulic Power Train Track Roller Frame
C9 Engines for Motor Graders Fuel Filter Differential Pressure - Test
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Filter Is Restricted
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290} Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Transfer Pump - Test
Location and Adjusting Procedure for the Bucket Stops {6001, 6107, 6119, 6129} Location and Adjusting Procedure for the Bucket Stops {6001, 6107, 6119, 6129}
2006/10/02 Use Only Cleaning Agents that are Water Based with the 212-1503 Parts Washer Kit {0680}