Camshaft - Disassemble
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件名称 | 数量 |
| A | 1P-2320 | 组合式拉拔器 | 1 |
开始:
- 拆下凸轮轴组件。 请参阅拆解和组装, "凸轮轴 - 拆卸"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将齿轮 (5) 从凸轮轴 (1) 上拆下。
注: 应将齿轮放在一个合适的支架上，以防止在拆解过程中损坏调速器飞锤。
- 将垫片 (4) 和月牙键 (2) 从凸轮轴 (1) 上拆下。
- 使用工具 (A) 将轴承 (3) 从凸轮轴 (1) 上拆下。
注: 确定轴承的方位，以方便安装。
Show/hide table
| |
| 图 1 | g01326129 |
|
典型示例 | |
Caterpillar Information System:
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Mounting and Dismounting
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
D6K Track-Type Tractor Machine Systems Bottom Guard - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System System Schematic
C-9 Engine for D6R Series II Track-Type Tractor CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
C-9 Engine for D6R Series II Track-Type Tractor CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
D6G Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) - Install
D6G Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Inlet) - Install
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Flywheel Scavenge) - Install
AD55B Underground Articulated Truck Battery Electrolyte Level - Check
Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004} Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
657G Wheel Tractor-Scraper Wheel Tractor Power Train Scavenge Pump and Mounting (Flywheel) - Remove
D6K Track-Type Tractor Machine Systems Bottom Guard - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Turbocharged Engines
Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050} Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Drive Shaft - Remove
C11 and C13 Engines and 14M and 16M Motor Graders CAN Data Link - Test
2006/09/18 A New Alternator Support and a New Belt are Used {1397, 1405}
D6G Series II Track-Type Tractor Machine Systems Bulldozer Brace - Remove and Install
D6K Track-Type Tractor Electrohydraulic Power Train Track Roller Frame
C9 Engines for Motor Graders Fuel Filter Differential Pressure - Test