Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
开始:
- 拆下 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将蓄电池断路开关转到断开位置。
- 在线束组件的连接上做出临时的识别标记。
Show/hide table
图 1 g01308285 典型示例 - 从交流发电机 (5) 上断开线束组件(未显示)。
- 从交流发电机 (5) 上拆下螺栓 (4) 和垫圈 (3)。
- 拆下垫圈 (7) 和螺母 (6)。 从安装支架上拆下螺栓 (8) 和交流发电机 (5)。
- 如有必要,卸下螺栓 (1),然后卸下调节连杆 (2)。
- 如有必要,安装调节连杆 (2),然后安装螺栓 (1) 并用手拧紧。
- 将交流发电机 (5) 安置在安装支架上。
- 安装螺栓 (8)、垫圈 (7) 和螺母 (6) 并用手拧紧。
- 安装螺栓 (4) 和垫圈 (3),用手拧紧。
- 安装 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。
注: 确保交流发电机皮带轮与曲轴皮带轮对准。 确保拧紧了所有的紧固件。
- 将线束组件(未显示)连接到交流发电机上。
- 将蓄电池断路开关转到接通位置。
Show/hide table
图 2 | g01308285 |
典型示例 |
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 55 Amp Alternator
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System System Schematic
C-9 Engine for D6R Series II Track-Type Tractor CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
C-9 Engine for D6R Series II Track-Type Tractor CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
D6G Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) - Install
D6G Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Inlet) - Install
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Flywheel Scavenge) - Install
AD55B Underground Articulated Truck Battery Electrolyte Level - Check
AD55B Underground Articulated Truck Backup Alarm - Test
AD55B Underground Articulated Truck Sampling Interval and Location of Sampling Valve
AD55B Underground Articulated Truck Filter and Screen Locations
AD55B Underground Articulated Truck Capacities (Refill)
D6K Track-Type Tractor Machine Systems Bottom Guard - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Mounting and Dismounting
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004} Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
657G Wheel Tractor-Scraper Wheel Tractor Power Train Scavenge Pump and Mounting (Flywheel) - Remove
D6K Track-Type Tractor Machine Systems Bottom Guard - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Turbocharged Engines
Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050} Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Drive Shaft - Remove
C11 and C13 Engines and 14M and 16M Motor Graders CAN Data Link - Test