Alternator - Remove and Install - 55 Amp Alternator
开始:
- 拆下 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将蓄电池断路开关转到断开位置。
- 在线束组件的连接上做出临时的识别标记。
Show/hide table
图 1 g01308282 典型示例 - 从交流发电机 (5) 上断开线束组件(未显示)。
- 从交流发电机 (5) 上拆下螺栓 (2) 和垫圈 (3)。
- 拆下紧固件 (6) 和 (7),然后从安装支架上拆下交流发电机 (5)。
- 如有必要,卸下螺栓 (2),然后卸下调节连杆 (4)。
- 如有必要,安装调节连杆 (4),然后安装螺栓 (1) 并用手拧紧。
- 将交流发电机 (5) 安置在安装支架上。
- 安装紧固件 (6) 和 (7) 并用手拧紧。
- 安装螺栓 (2) 和垫圈 (3),用手拧紧。
- 安装 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。
注: 确保交流发电机皮带轮与曲轴皮带轮对准。 确保拧紧了所有的紧固件。
- 将线束组件(未显示)连接到交流发电机上。
- 将蓄电池断路开关转到接通位置。
Show/hide table
图 2 | g01308282 |
典型示例 |
Caterpillar Information System:
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System System Schematic
C-9 Engine for D6R Series II Track-Type Tractor CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
C-9 Engine for D6R Series II Track-Type Tractor CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
D6G Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) - Install
D6G Series II Track-Type Tractor Power Train Relief Valve (Torque Converter Inlet) - Install
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Flywheel Scavenge) - Install
AD55B Underground Articulated Truck Battery Electrolyte Level - Check
AD55B Underground Articulated Truck Backup Alarm - Test
AD55B Underground Articulated Truck Sampling Interval and Location of Sampling Valve
AD55B Underground Articulated Truck Filter and Screen Locations
AD55B Underground Articulated Truck Capacities (Refill)
AD55B Underground Articulated Truck Tire Shipping Pressure
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Alternator - Remove and Install - 65 Amp and 85 Amp Alternators
D6K Track-Type Tractor Machine Systems Bottom Guard - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Mounting and Dismounting
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Disassemble
Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004} Installation Instructions for the 290-3531 Ride Control Ar (KIT){5004}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
657G Wheel Tractor-Scraper Wheel Tractor Power Train Scavenge Pump and Mounting (Flywheel) - Remove
D6K Track-Type Tractor Machine Systems Bottom Guard - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Turbocharged Engines
Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050} Installation of 6SU (S/N: D1Y; S6A; ECA; S6D; JCE; S6S; B6D; B6A) Bulldozer{6050}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Drive Shaft - Remove