Oil Pan - Remove and Install
拆卸步骤
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
注: 为便于安装,在所有管路、所有软管、所有线束组件及所有管上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和有助于防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将发动机机油排入合适的容器以便保存或废弃。 请参阅操作和保养手册, "发动机机油 - 更换"。
- 拆下螺栓 (1) 和管组件 (2) 。
Show/hide table
图 1 | g01288652 |
- 断开软管组件 (3) 和夹子 (4) 。
Show/hide table
图 2 | g01288654 |
- 从冷却器组件 (6) 两侧拆下支架 (7) 。
Show/hide table
图 3 | g01288655 |
- 拆下螺栓 (5) 和油底壳 (8) 。
安装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检验所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 将油底壳 (8) 和密封垫在发动机上定位,然后安装螺栓 (5) 。
Show/hide table
图 4 | g01288655 |
- 将支架 (7) 安装到冷却器总成 (6) 两端。
- 连接软管组件 (3) 和夹子 (4) 。
Show/hide table
图 5 | g01288654 |
- 将管组件 (2) 在机器上定位,然后安装螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 435 ± 20 N·m (321 ± 15 lb ft)。
Show/hide table
图 6 | g01288652 |
- 将机油加注到发动机中。 请参阅操作和保养手册, "发动机机油 - 更换"。
Caterpillar Information System:
657G Wheel Tractor-Scraper Engine Supplement Muffler - Remove and Install
D6G Series 2 Track-Type Tractor Emissions Certification Film
657G Wheel Tractor-Scraper Wheel Tractor Power Train Axle Housing - Remove and Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Remove
657G Wheel Tractor-Scraper Engine Supplement Air Cleaner - Remove and Install
Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620} Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620}
Reuse and Salvage for Connecting Rods {1218} Reuse and Salvage for Connecting Rods {1218}
657G Wheel Tractor-Scraper Engine Supplement Water Separator and Fuel Priming Pump - Remove and Install
657G Wheel Scraper Power Train Oil Filter Base (Transmission) - Remove and Install
657G Wheel Scraper Power Train Transmission Hydraulic Control - Install
657G Wheel Scraper Power Train Transmission Hydraulic Control - Remove
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Major)
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Top End)
657G Wheel Tractor-Scraper Engine Supplement Engine Support (Rear) - Remove and Install
2006/08/07 A New Kit for the Cooling System Pressure Cap is Available {1353, 1354, 1382, 1392, 7405}
D7G Series 2 and D7G Series II Track-Type Tractors Lifting and Tying Down the Machine
966H and 972H Wheel Loaders Drive Shaft Support Bearing - Lubricate
966H and 972H Wheel Loaders Drive Shaft Universal Joints - Lubricate
657G Wheel Tractor-Scraper Engine Supplement Transmission Oil Cooler - Remove and Install
D7G Series 2 and D7G Series II Track-Type Tractors Additional Messages
D7G Series 2 and D7G Series II Track-Type Tractors Capacities (Refill)
Effectivity of the Upgrades to Remanufactured Transmissions, Torque Converters, and Wheel Assemblies{3030, 3101, 4051} Effectivity of the Upgrades to Remanufactured Transmissions, Torque Converters, and Wheel Assemblies{3030, 3101, 4051}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Transmission Hydraulic Control - Remove