Transmission Hydraulic Control - Install
安装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检验所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 安装歧管 (23) 和螺栓 (22) 。 拧紧螺栓 (22) 至扭矩为 48 ± 4 N·m (35 ± 3 lb ft)。
Show/hide table
图 1 | g01288293 |
- 安装管 (24) 、阀体 (25) 和螺栓 (26) 。 拧紧螺栓 (26) 至扭矩为 48 ± 4 N·m (35 ± 3 lb ft)。
- 安装盘 (27) 和螺栓 (28) 。
- 安装阀 (21) 、螺栓 (20) 和螺栓 (19) 。
Show/hide table
图 2 | g01288264 |
- 需要两个人,安装阀 (18) 、螺栓 (17) 和螺栓 (16) 。 拧紧螺栓 (17) 至扭矩为 48 ± 4 N·m (35 ± 3 lb ft)。
Show/hide table
图 3 | g01288262 |
- 将 O 形密封圈 (15) 、联轴节组件 (13) 和挡圈 (14) 安装到阀 (5) 上。
Show/hide table
图 4 | g01289153 |
- 安装套筒 (12) 和 O 形密封圈。
- 安装盘 (6) 和螺栓 (9) 。
Show/hide table
图 5 | g01288259 |
- 安装阀 (5) 和螺栓 (7) 。 拧紧螺栓 (7) 至扭矩为 48 ± 4 N·m (35 ± 3 lb ft)。
- 重新安置线束组件 (8) 。
- 连接线束组件 (3) 和线束组件 (11) 。
- 连接夹子 (4) 和夹子 (10) 。
- 安装盖 (1) 和 (2) 。
Show/hide table
图 6 | g01288258 |
End By: 安装推拉挂钩。 请参阅 拆解和组装, "推拉挂钩 - 拆卸和安装"。
Caterpillar Information System:
657G Wheel Scraper Power Train Transmission Hydraulic Control - Remove
953D Track-Type Loader Engine Supplement Alternator - Remove and Install
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Solenoid Valve (Transmission Clutch)
Ampseal 16 Connector Peripheral Seal Servicing{7553} Ampseal 16 Connector Peripheral Seal Servicing{7553}
Tier I Level Emissions Engine Repower for a 990 Wheel Loader {1000} Tier I Level Emissions Engine Repower for a 990 Wheel Loader {1000}
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Speed Sensor (Torque Converter Output) (Transmission Output)
953D Track-Type Loader Engine Supplement Fuel Filter Base and Priming Pump - Remove and Install
2006/09/11 Correction to Operation and Maintenance Manual, "Differential and Final Drive Oil Level - Check {3258, 4050}
2006/09/11 Correction to Operation and Maintenance Manual, "Differential and Final Drive Oil - Change {3258, 4050}
2006/09/11 Correction to Operation and Maintenance Manual, "Sampling Interval and Location of Sampling Valve" {1000, 1318, 1348, 3080, 4070, 4250, 4300, 5050, 7000, 7542}
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Steering System Steering Neutralizer Valve
657G Wheel Tractor-Scraper Wheel Tractor Power Train Quick-Release Valve (Differential Lock) - Remove and Install
657G Wheel Scraper Power Train Oil Filter Base (Transmission) - Remove and Install
657G Wheel Tractor-Scraper Engine Supplement Water Separator and Fuel Priming Pump - Remove and Install
Reuse and Salvage for Connecting Rods {1218} Reuse and Salvage for Connecting Rods {1218}
Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620} Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620}
657G Wheel Tractor-Scraper Engine Supplement Air Cleaner - Remove and Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Remove
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Axle Housing - Remove and Install
D6G Series 2 Track-Type Tractor Emissions Certification Film
657G Wheel Tractor-Scraper Engine Supplement Muffler - Remove and Install
657G Wheel Tractor-Scraper Engine Supplement Oil Pan - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Major)