Oil Filter Base (Transmission) - Remove and Install
拆卸步骤
开始:
- 卸下推拉挂钩。 请参阅拆解和组装, "推拉挂钩 - 拆卸和安装"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 拆卸盖 (1) 。
Show/hide table
图 1 | g01288325 |
- 卸下壳体 (6) 和滤芯。
Show/hide table
图 2 | g01288326 |
- 卸下螺栓 (3) 和滤清器底座 (2) 。
- 卸下螺栓 (5) 和接头 (4) 。
安装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检验所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 安装接头 (4) 和螺栓 (5) 。
Show/hide table
图 3 | g01288326 |
- 安装滤清器底座 (2) 和螺栓 (3) 。
- 安装壳体 (6) 和滤芯。
- 安装盖 (1) 。
Show/hide table
图 4 | g01288325 |
End By: 安装推拉挂钩。 请参阅 拆解和组装, "推拉挂钩 - 拆卸和安装"。
Caterpillar Information System:
657G Wheel Scraper Power Train Transmission Hydraulic Control - Install
657G Wheel Scraper Power Train Transmission Hydraulic Control - Remove
953D Track-Type Loader Engine Supplement Alternator - Remove and Install
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Solenoid Valve (Transmission Clutch)
Ampseal 16 Connector Peripheral Seal Servicing{7553} Ampseal 16 Connector Peripheral Seal Servicing{7553}
Tier I Level Emissions Engine Repower for a 990 Wheel Loader {1000} Tier I Level Emissions Engine Repower for a 990 Wheel Loader {1000}
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Speed Sensor (Torque Converter Output) (Transmission Output)
953D Track-Type Loader Engine Supplement Fuel Filter Base and Priming Pump - Remove and Install
2006/09/11 Correction to Operation and Maintenance Manual, "Differential and Final Drive Oil Level - Check {3258, 4050}
2006/09/11 Correction to Operation and Maintenance Manual, "Differential and Final Drive Oil - Change {3258, 4050}
2006/09/11 Correction to Operation and Maintenance Manual, "Sampling Interval and Location of Sampling Valve" {1000, 1318, 1348, 3080, 4070, 4250, 4300, 5050, 7000, 7542}
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Steering System Steering Neutralizer Valve
657G Wheel Tractor-Scraper Engine Supplement Water Separator and Fuel Priming Pump - Remove and Install
Reuse and Salvage for Connecting Rods {1218} Reuse and Salvage for Connecting Rods {1218}
Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620} Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620}
657G Wheel Tractor-Scraper Engine Supplement Air Cleaner - Remove and Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Remove
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Axle Housing - Remove and Install
D6G Series 2 Track-Type Tractor Emissions Certification Film
657G Wheel Tractor-Scraper Engine Supplement Muffler - Remove and Install
657G Wheel Tractor-Scraper Engine Supplement Oil Pan - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Major)
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Top End)