Axle Housing - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 1U-9200     | 杠杆式拔拉起重机     | 1     |
138-7574 | 连杆支架     | 1     |
开始:
- 卸下行车制动器。 请参阅拆解和组装, "行车制动器 - 拆卸"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将适当的起吊设备和工具 (A) 连接在车轴壳体 (1) 上。 车轴壳体 (1) 的重量约为 453 kg (1000 lb)。 卸下螺栓 (2) ,卸下车轴壳体 (1) 。
Show/hide table
图 1 | g01288463 |
Show/hide table
图 2 | g00530085 |
- 从车轴壳体 (1) 上卸下 O 形密封圈 (3) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 1U-9200     | 杠杆式拔拉起重机     | 1     |
138-7575 | 连杆支架     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检验所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 在要密封的 O 形密封圈上涂敷润滑剂。 将 O 形密封圈 (3) 安装到车轴壳体上。
Show/hide table
图 3 | g00530085 |
- 将适当的起吊设备和工具 (A) 连接在车轴壳体 (1) 上。 车轴壳体 (1) 的重量约为 453 kg (1000 lb)。
Show/hide table
图 4 | g01288463 |
- 安装螺栓 (1) 和垫圈。 按照交替的星形模式拧紧螺栓 (1) 至扭矩为 725 ± 150 N·m (534 ± 110 lb ft)。 按照交替的星形模式拧紧螺栓 (1) 至扭矩为 1050 ± 150 N·m (774 ± 110 lb ft)。
End By: 安装行车制动器。 请参阅 拆解和组装, "行车制动器 - 安装"。
Caterpillar Information System:
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Install
657G Wheel Tractor-Scraper Wheel Tractor Power Train Wheel, Wheel Bearings and Duo-Cone Seals - Remove
657G Wheel Tractor-Scraper Engine Supplement Air Cleaner - Remove and Install
Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620} Procedures For Installing Multi-Velocity Program (MVP) in the D6R Series III{1408, 7620}
Reuse and Salvage for Connecting Rods {1218} Reuse and Salvage for Connecting Rods {1218}
657G Wheel Tractor-Scraper Engine Supplement Water Separator and Fuel Priming Pump - Remove and Install
657G Wheel Scraper Power Train Oil Filter Base (Transmission) - Remove and Install
657G Wheel Scraper Power Train Transmission Hydraulic Control - Install
657G Wheel Scraper Power Train Transmission Hydraulic Control - Remove
953D Track-Type Loader Engine Supplement Alternator - Remove and Install
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Solenoid Valve (Transmission Clutch)
Ampseal 16 Connector Peripheral Seal Servicing{7553} Ampseal 16 Connector Peripheral Seal Servicing{7553}
D6G Series 2 Track-Type Tractor Emissions Certification Film
657G Wheel Tractor-Scraper Engine Supplement Muffler - Remove and Install
657G Wheel Tractor-Scraper Engine Supplement Oil Pan - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Major)
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Top End)
657G Wheel Tractor-Scraper Engine Supplement Engine Support (Rear) - Remove and Install
2006/08/07 A New Kit for the Cooling System Pressure Cap is Available {1353, 1354, 1382, 1392, 7405}
D7G Series 2 and D7G Series II Track-Type Tractors Lifting and Tying Down the Machine
966H and 972H Wheel Loaders Drive Shaft Support Bearing - Lubricate
966H and 972H Wheel Loaders Drive Shaft Universal Joints - Lubricate
657G Wheel Tractor-Scraper Engine Supplement Transmission Oil Cooler - Remove and Install
D7G Series 2 and D7G Series II Track-Type Tractors Additional Messages