Engine Enclosure Group - Remove and Install
Removal Procedure
- Disconnect the battery. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Disconnect".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove plugs (2) from panel assembly (1) .
Show/hide table
Illustration 1 | g01207994 |
- Remove bolts (3) in order to remove panel assembly (1) .
Show/hide table
Illustration 2 | g01207997 |
- Repeat Steps 2 and 3 for the opposite side.
- Open door assembly (4) in order to remove door assembly (4) from the hinges.
Show/hide table
Illustration 3 | g01207998 |
- Repeat Step 5 for the opposite side.
- Open door assembly for control panel (5) in order to remove door assembly for control panel (5) from the hinges.
Show/hide table
Illustration 4 | g01207999 |
- Remove panel assembly (6) .
Show/hide table
Illustration 5 | g01208001 |
- Remove bolts (8) in order to disconnect exhaust elbow (7) from the engine. Remove the gasket.
Show/hide table
Illustration 6 | g01208003 |
- Attach a suitable lifting device to engine enclosure group (9). The weight of engine enclosure group (9) is approximately 110 kg (240 lb).
Show/hide table
Illustration 7 | g01208010 |
- Remove bolts (10) in order to remove engine enclosure group (9) .
Show/hide table
Illustration 8 | g01208011 |
Installation Procedure
- Attach a suitable lifting device to engine enclosure group (9). The weight of engine enclosure group (9) is approximately 110 kg (240 lb).
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 9 | g01208010 |
- Position engine enclosure group (9) on the base and install bolts (10) .
Show/hide table
Illustration 10 | g01208011 |
- Position the gasket on exhaust elbow (7). Connect exhaust elbow (7) to the engine and install bolts (8) .
Show/hide table
Illustration 11 | g01208003 |
- Install panel assembly (6) .
Show/hide table
Illustration 12 | g01208001 |
- Install door assembly for control panel (5) on the hinges.
Show/hide table
Illustration 13 | g01207999 |
- Install door assembly (4) on the hinges.
Show/hide table
Illustration 14 | g01207998 |
- Repeat Step 6 for the opposite side.
- Position panel assembly (1) on the engine enclosure group and install bolts (3) .
Show/hide table
Illustration 15 | g01207997 |
- Install plugs (2) on panel assembly (1) .
Show/hide table
Illustration 16 | g01207994 |
- Repeat Steps 8 and 9 for the opposite side.
- Connect the battery. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Disconnect".
Caterpillar Information System:
2005/10/03 Caterpillar Warranty Claims on Cylinder Head Valves {1105}
2005/10/03 Starting the Engine with Jumper Cables on Machines with an Electric Starter {1000, 7000}
345C MHPU Mobile Hydraulic Power Unit Machine Systems Fuel Tank - Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Fuel Tank - Remove
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Actuator Motor (Air Distributor) - Remove and Install
C32 Petroleum Engines Fuel Temperature Sensor - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Window Wiper Motor - Remove and Install - Lower
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Final Drive - Disassemble
C32 Petroleum Engines Fuel Pressure Sensor - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Auxiliary Water Pump - Assemble
C32 Petroleum Engines Engine Oil Pressure Sensor - Remove and Install
320E and 323E Excavators Machine System Specifications Solenoid Valve (Quick Coupler)
C32 Petroleum Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C32 Petroleum Engines Inlet Air Temperature Sensor - Remove and Install
C175 Generator Set Engines Exhaust Elbow - Remove and Install
TH48-E80 Petroleum Transmission Power Train Electronic Control System Speed Sensor (Transmission Output) - Replace
2005/10/01 Caterpillar Warranty Claims on Cylinder Head Valves {1105}
C175 Generator Set Engines Crankshaft Front Seal - Remove
2005/10/03 Caterpillar Warranty Claims on Cylinder Head Valves {1105}
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Seat Suspension - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Seat Support - Remove and Install
C175 Generator Set Engines Crankshaft Front Seal - Install
C32 Petroleum Engines Camshaft Bearings - Remove