Final Drive - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-2420     | 变速箱修复台总成     | 1     |
B     | 138-7573     | 连杆支架     | 2     |
C     | 1P-1860     | 挡圈钳     | 1     |
D     | 4C-8359     | 吊环螺栓     | 3     |
E     | 4C-8359     | 吊环螺栓     | 2     |
F     | 138-7574     | 连杆支架     | 2     |
开始:
- 拆下终传动。 请参阅此手册中的拆解和组装, "终传动 和 行驶马达 - 拆卸"。
- 拆解之前,彻底清洁终传动和行驶马达的外部。
- 将连接器 (1) 从终传动 (2) 上拆下。
Show/hide table
图 1 | g01207795 |
- 将适当的起吊设备连接到终传动上,然后将终传动 (2) 翻转 180 度。 终传动 (2) 的重量约为 590 kg (1300 lb)。
- 将终传动固定到工具 (A) 上。 为便于组装,在终传动区域标出对准标记。 所有零件必须重新安装在其原来的位置。
Show/hide table
图 2 | g01207796 |
- 拆下终传动盖上的内六角头螺钉 (3) 。
- 如图所示,将工具 (B) 和适当的起吊设备固定到盖 (5) 上。 盖 (5) 的重量约为 52 kg (115 lb)。
Show/hide table
图 3 | g01207801 |
- 拆下将盖固定在相应位置的螺栓 (4) 和垫圈。
- 利用软面锤破坏盖 (5) 和齿圈间的密封。 拆下盖 (5) 。 盖 (5) 的重量为 52 kg (115 lb)。
- 将隔套 (6) 从盖上拆下。
Show/hide table
图 4 | g01207835 |
- 将垫片 (7) 从盖上拆下。
Show/hide table
图 5 | g01207845 |
- 从盖上拆下内六角头螺栓 (8) 和齿圈 (9) 。
- 从行星齿轮架组件 (11) 上拆下太阳齿轮 (10) 。 通过垂直升起行星齿轮架组件,拆下行星齿轮架组件 (11) 。
Show/hide table
图 6 | g01207864 |
- 如下所示,拆解行星齿轮架组件 (11) 。
- 拆下隔套 (12) 。 隔套位于行星齿轮架组件 (11) 内太阳齿轮的每侧。
注: 行星齿轮 (15) 上可能压印有识别标记 "L"。 记下识别标记相对于行星齿轮架的位置,以便于组装。
Show/hide table图 7 g01207865
- 用工具 (C) 拆下挡圈 (13) 。
Show/hide table图 8 g01207897
- 从行星齿轮架上拆下止推垫圈 (14) 和行星齿轮 (15) 。
- 将轴承 (16) 从行星齿轮上拆下。
- 对其他两个行星齿轮重复步骤 13.b 至 13.d。
- 利用螺丝刀将挡圈 (17) 从行星齿轮架上拆下。 将太阳齿轮 (18) 从行星齿轮架上拆下。
Show/hide table图 9 g01208035
- 拆下隔套 (12) 。 隔套位于行星齿轮架组件 (11) 内太阳齿轮的每侧。
- 将工具 (D) 和适当的起吊设备固定到行星齿轮架组件 (19) 上,如图所示。 通过垂直上拉行星齿轮架组件,拆下行星齿轮架组件 (19) 。 行星齿轮架组件 (19) 的重量大约为 45 kg (100 lb)。
Show/hide table
图 10 | g01208136 |
- 按照如下方法,拆解行星齿轮架组件 (19) :
注: 隔套 (20) 可能留在行星齿轮架组件 (19) 或 (28) 上。 请参阅步骤 17。
- 从行星齿轮架组件 (19) 上拆下隔套 (20) 。
Show/hide table图 11 g01208162
- 使用锤子和冲头将弹簧销 (21) 打入行星齿轮轴 (22) 。
Show/hide table图 12 g01208169
- 从行星齿轮架组件上拆下行星齿轮轴 (22) 、两个止推垫圈 (23) 和行星齿轮 (24) 。
注: 行星齿轮 (24) 上可能压印有识别标记 "M"。 记下识别标记相对于行星齿轮架的位置,以便于组装。
Show/hide table图 13 g01208189
- 将轴承 (25) 从行星齿轮上拆下。
- 使用锤子和冲头从行星齿轮轴 (22) 拆下弹簧销 (21) 。
- 重复步骤 15.b 至 15.e,以便从行星齿轮架上拆下其他两个行星齿轮。
- 使用螺丝刀拆下挡圈 (26) 。 将太阳齿轮 (27) 从行星齿轮架上拆下。
Show/hide table图 14 g01208245
- 如果隔套 (20) 在步骤 15.a 内未拆下,则此时将隔套从行星齿轮架组件 (28) 上拆下。
Show/hide table
图 15 | g01208253 |
- 将工具 (E) 和适当的起吊设备固定到行星齿轮架组件 (28) 上,如图所示。 拆下行星齿轮架组件 (28) 。 行星齿轮架组件 (28) 的重量大约为 64 kg (140 lb)。
Show/hide table
图 16 | g01208256 |
- 按照如下方法,拆解行星齿轮架组件 (28) :
- 使用锤子和冲头将弹簧销 (29) 打入行星齿轮轴 (30) 。
Show/hide table图 17 g01208265
- 从行星齿轮架组件上拆下行星齿轮轴 (30) 、止推垫圈 (31) 和行星齿轮 (32) 。
注: 行星齿轮 (32) 上可能压印有识别标记 "N"。 记下识别标记相对于行星齿轮架的位置,以便于组装。
Show/hide table图 18 g01208280
- 从行星齿轮上拆下轴承 (33) 。
- 使用锤子和冲头将弹簧销 (29) 打出行星齿轮轴 (30) 。
- 重复步骤 18.a 至 18.d,以便从行星齿轮架上拆下其他三个行星齿轮。
- 将工具 (E) 和适当的起吊设备固定到齿圈 (34) 上,如图所示。 将齿圈 (34) 从链轮壳 (35) 上拆下。 齿圈 (34) 的重量约为 82 kg (180 lb)。
Show/hide table
图 19 | g01208300 |
- 从链轮壳 (35) 拆下 O 形密封圈 (36) 。
Show/hide table
图 20 | g01208542 |
- 从连接器齿轮 (38) 拆下螺栓 (37) 。 标记连接器 (38) ,以便于组装。
Show/hide table
图 21 | g01208553 |
- 将适当的顶出螺栓 (39) 装入连接齿轮 (38) 内,如图所示。 通过均匀上紧顶出螺栓松开连接齿轮 (38) 。 将连接齿轮从马达壳体上拆下。
Show/hide table
图 22 | g01208572 |
- 从马达壳体拆下垫片 (40) 。
注: 内侧和外侧轴承内圈 (42) 通过滑动配合安装在马达壳体上。 从马达壳体上拆卸链轮壳 (35) 时,内侧轴承内圈 (42) 可能留在链轮壳或马达壳体上。
Show/hide table
图 23 | g01208578 |
Show/hide table
图 24 | g01208625 |
- 将工具 (F) 和适当的起吊设备连接到链轮壳体 (35) 上,如图所示。 将链轮壳从马达壳体上分离。 链轮壳 (35) 的重量为 127 kg (280 lb)。
- 将定位销从马达壳体上拆下。
Show/hide table
图 25 | g01208626 |
- 将双锥形密封总成 (41) 从马达壳体上拆下。
- 如果内侧轴承内圈 (42) 留在马达壳体上,则拆卸下轴承内圈。
- 将双锥形密封总成 (43) 从链轮壳上拆下。
Show/hide table
图 26 | g01208633 |
- 如果内侧轴承内圈 (42) 留在链轮壳上,则拆卸下轴承内圈。
- 从链轮壳上拆下轴承外圈。
Caterpillar Information System:
C32 Petroleum Engines Fuel Pressure Sensor - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Auxiliary Water Pump - Assemble
C32 Petroleum Engines Engine Oil Pressure Sensor - Remove and Install
C32 Petroleum Engines Coolant Temperature Sensor - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Seat - Remove and Install
C32 Petroleum Engines Crankshaft Position Sensor - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Pilot Valve (Travel) - Install
3512C Engine for 785D Off-Highway Truck/Tractors Engine Design
3512C and 3516C Marine Engines Engine Design
C32 Petroleum Engines Camshaft Position Sensor - Remove and Install
C-9 Industrial Engine Maintenance Interval Schedule
TH48-E80 Petroleum Transmission Power Train Electronic Control System Quick To Neutral Function
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Window Wiper Motor - Remove and Install - Lower
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner
C32 Petroleum Engines Fuel Temperature Sensor - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Actuator Motor (Air Distributor) - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Fuel Tank - Remove
345C MHPU Mobile Hydraulic Power Unit Machine Systems Fuel Tank - Install
2005/10/03 Starting the Engine with Jumper Cables on Machines with an Electric Starter {1000, 7000}
2005/10/03 Caterpillar Warranty Claims on Cylinder Head Valves {1105}
C1.5 and C2.2 Generator Set Engines Engine Enclosure Group - Remove and Install
320E and 323E Excavators Machine System Specifications Solenoid Valve (Quick Coupler)
C32 Petroleum Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C32 Petroleum Engines Inlet Air Temperature Sensor - Remove and Install