Crankshaft Position Sensor - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect harness assembly (1).
- Remove bolt (3) and crankshaft position sensor (2).
- Remove the O-ring seal from crankshaft position sensor (2).
Show/hide table
| |
| Illustration 1 | g01207682 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install a new O-ring seal on crankshaft position sensor (2). Lubricate the O-ring seal with clean engine oil.
- Install crankshaft position sensor (2) in the front housing. Install bolt (3). Tighten bolt (3) to a torque of
28 ± 7 N·m (21 ± 5 lb ft) . - Connect harness assembly (1).
Show/hide table
|
| |
| Illustration 2 | g01207682 |
Caterpillar Information System:
345C MHPU Mobile Hydraulic Power Unit Machine Systems Pilot Valve (Travel) - Install
3512C Engine for 785D Off-Highway Truck/Tractors Engine Design
3512C and 3516C Marine Engines Engine Design
C32 Petroleum Engines Camshaft Position Sensor - Remove and Install
C-9 Industrial Engine Maintenance Interval Schedule
TH48-E80 Petroleum Transmission Power Train Electronic Control System Quick To Neutral Function
TH48-E80 Petroleum Transmission Power Train Electronic Control System Lockup Clutch Disable Function
3500C Marine Engines Engine Design
C27 and C32 Generator Set Engines Speed Control (Switch) - Test
793D Off-Highway Truck Power Train Liquid Level Switch (Torque Converter Oil)
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Charging System - Test
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Exhaust Temperature Is Too High
345C MHPU Mobile Hydraulic Power Unit Machine Systems Seat - Remove and Install
C32 Petroleum Engines Coolant Temperature Sensor - Remove and Install
C32 Petroleum Engines Engine Oil Pressure Sensor - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Auxiliary Water Pump - Assemble
C32 Petroleum Engines Fuel Pressure Sensor - Remove and Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Final Drive - Disassemble
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Window Wiper Motor - Remove and Install - Lower
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner
C32 Petroleum Engines Fuel Temperature Sensor - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Actuator Motor (Air Distributor) - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Fuel Tank - Remove
345C MHPU Mobile Hydraulic Power Unit Machine Systems Fuel Tank - Install