Inlet and Exhaust Valves - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 333-0758 | 气门弹簧压缩器 | 1 |
开始:
- 拆下电子单体喷油器。 请参阅拆解和组装, "电子单体喷油器 - 拆卸"。
- 拆卸缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
- 将工具 (A) 安装到电子单体喷油器的孔内。 请参阅插图 2。
Show/hide table
图 3 g01851274 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 将工具 (A) 的板安装到气门弹簧上。 请参阅插图 3。 将螺母安装到螺柱上。 拧紧螺母以压缩气门弹簧 (2)。 拆下挡圈锁 (1)。
Show/hide table
图 4 g01206605 - 拆下工具 (A)。 拆卸转盘 (3)、外弹簧 (4)、内弹簧 (5)、气门密封 (6)、挡圈 (7) 和气门 (8)。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
图 1 | g01206603 |
Show/hide table
图 2 | g01207146 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 333-0758 | 气门弹簧压缩器 | 1 |
- 安装气门 (8)、挡圈 (7)、气门密封 (6)、内弹簧 (5)、外弹簧 (4) 和转盘 (3)。
Show/hide table
图 6 g01206603 Show/hide table图 7 g01228542 Show/hide table图 8 g01851274 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 使用工具 (A),压缩气门弹簧 (2)。 安装挡圈锁 (1)。 释放气门弹簧 (2) 上的张紧力。 拆下工具 (A)。 将螺钉起子安装到喷油器孔内。 慢慢地转动发动机,直到活塞低于上止点约
25 mm (1.00 in) 。 用软面锤轻轻敲打气门顶部,以确保挡圈锁 (1) 正确就位。
Show/hide table
图 5 | g01206605 |
结束:
- 安装缸盖。 请参阅拆解和组装, "缸盖- 安装"。
- 安装电子单体喷油器。 请参阅拆解和组装, "电子单体喷油器 - 安装"。
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Pressure Differential Switch
3500C Marine Engines Engine Design
C32 Petroleum Engines Camshaft - Remove
C175-16 Locomotive Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
C7 Industrial Engine Sensors and Electrical Components
C27 and C32 Generator Set Engines Ether Injection System - Test
C32 Petroleum Engines Cylinder Head - Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7 Industrial Engine Engine Description
C32 Petroleum Generator Sets Reference Material
C7.1 Engines for Caterpillar Built Machines Water Temperature Regulator and Housing
C27 and C32 Engines Fuel System
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Check Valve (Counterweight Circuit) - Install
C27 and C32 Engines Engine Oil Pressure - Test
C27 and C32 Generator Set Engines Emergency Stop Switch Circuit - Test
C7 Industrial Engine Plate Locations and Film Locations
C27 and C32 Engines Cooling System
2005/10/17 Power Relay Used for Isolation on VR6 Voltage Regulators {4467, 4493}
2005/11/07 Heavy Duty Ring Terminals Are Now Being Used on High Voltage Generators {7553}
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines 5 Volt Sensor Supply Circuit - Test
C7 Industrial Engine Refill Capacities and Recommendations
C7 Industrial Engine Diagnostic Flash Code Retrieval
C7 Industrial Engine Reference Material
C7.1 Engines for Caterpillar Built Machines Water Temperature Regulator - Test