Inlet and Exhaust Valve Guides - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 283-0052 | 气门导管冲头 | 1 |
开始:
- 拆下进气阀和排气阀。 请参阅拆解和组装, "进气阀与排气阀 - 拆卸和安装"。
- 旋转缸盖。 采用工具 (A) 和适当的锤子将气门导管 (1) 从缸盖上拆下。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
图 1 | g01206606 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 283-0052 | 气门导管冲头 | 1 |
B | 284-1503 | 套环 | 1 |
- 安装前用清洁的机油涂在气门导管的外侧。 使用工具 (A)、工具 (B) 和适当的锤子将气门导管 (1) 安装到缸盖中。 气门导管 (1) 必须从缸盖表面伸出
42.0 ± 0.50 mm (1.65 ± 0.020 in) 。
Show/hide table
图 2 | g01211260 |
结束:
- 安装进气阀和排气阀。 请参阅拆解和组装, "进气阀与排气阀 - 拆卸和安装"。
Caterpillar Information System:
C7 Industrial Engine Engine Description
C32 Petroleum Generator Sets Reference Material
C7.1 Engines for Caterpillar Built Machines Water Temperature Regulator and Housing
C27 and C32 Engines Fuel System
2005/10/03 Responsibilities for Emission Certified Engines {1000}
C7.1 Engines for Caterpillar Built Machines Lubrication System
C15 Engine Maintenance Interval Schedule
C15 Engine Engine Crankcase Breather - Clean
C15 Engine Electronics Grounding Stud - Inspect/Clean/Tighten
Installation and Initial Start-Up Procedure for G3500 A3 Engines {1000} Installation and Initial Start-Up Procedure for G3500 A3 Engines {1000}
C1.5 and C2.2 Generator Set Engines Generator - Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Counterweight Circuit) - Install
C32 Petroleum Engines Cylinder Head - Install
C27 and C32 Generator Set Engines Ether Injection System - Test
C7 Industrial Engine Sensors and Electrical Components
C175-16 Locomotive Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
C32 Petroleum Engines Camshaft - Remove
3500C Marine Engines Engine Design
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Pressure Differential Switch
C175-16 and C175-20 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Check Valve (Counterweight Circuit) - Install
C27 and C32 Engines Engine Oil Pressure - Test
C27 and C32 Generator Set Engines Emergency Stop Switch Circuit - Test
C7 Industrial Engine Plate Locations and Film Locations