Generator - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 2     |
- Attach a suitable lifting device to rotor assembly (19). The weight of rotor assembly (19) is approximately 34 kg (75 lb). Position rotor assembly (19) on flywheel (21). Install bolts (20) .
Show/hide table
Illustration 1 | g01206237 |
- Attach Tooling (A) and a suitable lifting device to generator housing (13). The weight of generator housing (13) is approximately 68 kg (150 lb).
Show/hide table
Illustration 2 | g01206235 |
- Position generator housing (13) on flywheel housing (18). Install bolts (17). Raise generator housing (13) and remove suitable cribbing under flywheel housing (18) .
- Remove Tooling (A) and a suitable lifting device from generator housing (13) .
Show/hide table
Illustration 3 | g01206212 |
- Install bolts (16) on generator housing (13) .
Show/hide table
Illustration 4 | g01206208 |
- Install guard assembly (15) and bolts (14) on generator housing (13) .
Show/hide table
Illustration 5 | g01206186 |
- Connect harness assemblies (11) and (12) .
Show/hide table
Illustration 6 | g01206176 |
- Connect harness assemblies (6), (7), (8), (9), and (10) .
Show/hide table
Illustration 7 | g01206174 |
- Connect nut (5) to operator control panel (3). Install cover (4) on operator control panel (3) .
Show/hide table
Illustration 8 | g01206173 |
- Install air cleaner assembly (2). Connect hose (1) to air cleaner assembly (2) .
Show/hide table
Illustration 9 | g01206168 |
End By: Install the engine enclosure. Refer to Disassembly and Assembly, "Engine Enclosure - Remove and Install".
Caterpillar Information System:
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Counterweight Circuit) - Install
G3500 A3 Engines System Configuration Parameters - Oxygen Feedback
C13 and C15 On-Highway Engines Reference Material
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Manual Ball Valve (Counterweight Circuit) - Install
C1.5 and C2.2 Generator Set Engines Generator - Remove
G3304 and G3306 Engines Electric Starting Motor
325D and 329D Excavators and 325D Material Handler Machine System Specifications Relief Valve (Pilot) - Front Lines
C175 Generator Set Engines Piston Cooling Jets - Remove and Install
C7 and C9 On-highway Engines Engine Operation
C15 Engine Refill Capacities and Recommendations
G3500 A3 Engines Engine Monitoring System - Oxygen Feedback
C15 Engine Information Plate
Installation and Initial Start-Up Procedure for G3500 A3 Engines {1000} Installation and Initial Start-Up Procedure for G3500 A3 Engines {1000}
C15 Engine Electronics Grounding Stud - Inspect/Clean/Tighten
C15 Engine Engine Crankcase Breather - Clean
C15 Engine Maintenance Interval Schedule
C7.1 Engines for Caterpillar Built Machines Lubrication System
2005/10/03 Responsibilities for Emission Certified Engines {1000}
C27 and C32 Engines Fuel System
C7.1 Engines for Caterpillar Built Machines Water Temperature Regulator and Housing
C32 Petroleum Generator Sets Reference Material
C7 Industrial Engine Engine Description
C175-16 and C175-20 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C32 Petroleum Engines Cylinder Head - Install