Unit Injector Sleeve - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 372-7975     | 喷油器套筒工具     | 1     |
E     | -     | Loctite 620     | -     |
F     | 4C-5552     | 大号孔刷     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 彻底清洁单体喷油器套管和单体喷油器孔径。 工具 (F) 可能用于孔径。
- 将清洁的发动机机油涂抹到 O 形密封圈 (1) 上。
Show/hide table
图 1 | g03500578 |
- 将一薄层工具 (E) 涂敷在单体喷油器套管 (2) 外缘的表面 (Z) 。
- 使用工具 (A) 和锤子将单体喷油器套管 (2) 安装到缸盖中。
Show/hide table
图 2 | g03500637 |
- 有关正确的加注步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
注: 向发动机加注燃油或冷却液之前先在 21 °C (70 °F) 下使工具 (E) 粘合两小时。 温度越低,需要的固化时间越长。
End By: 安装单体喷油器。
Caterpillar Information System:
3500B Series II Marine Engines Prelubrication System
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove
651E and 657E Wheel Tractor-Scrapers Hydraulic System Cylinder Cycle Time - Check
C7 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
966F Series II Wheel Loader Power Train Transmission Hydraulic Control Valve - Disassemble
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
Supplemental Documentation for the Payload Control System{7494} Supplemental Documentation for the Payload Control System{7494}
953C Track-Type Loader Cooling System Extended Life Coolant Extender - Add
613C Series II Wheel Tractor-Scraper Hydraulic System Elevator Circuit
651E and 657E Wheel Tractor-Scrapers Power train Operational Checks
613C Series II Wheel Tractor-Scraper Hydraulic System Ejector Circuit
AD30 Underground Articulated Truck Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
AD30 Underground Articulated Truck Ejector Cylinder Bearing - Lubricate
Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050} Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
2003/03/31 Correction to Disassembly and Assembly , "Axle Shaft Assemblies" {3259}
3508B Engine for Caterpillar Built Machines Air Cleaner
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group
2003/04/07 Special Instruction, REHS1353, "Field Installation of the Engine Speed Control" Is Available {1915}
2003/03/31 Correction to Disassembly and Assembly , "Gear Pump (Axle Oil Cooler) - Remove and Install" {5073}
2003/03/31 Correction to Disassembly and Assembly , "Drive Axle Shafts" {3259}
2003/03/31 Correction to Disassembly and Assembly , "Axle Shaft - Remove and Install" {3259}
G3500B Engines Start/Stop Control