Crankshaft Gear - Remove and Install
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 8B-7551 | 轴承拉拔器 | 1 |
| 8B-7549 | 拉拔器腿 | 2 | |
| 3H-0465 | 压拉器板 | 4 | |
| 6B-6682 | 全高螺母 | 2 | |
| 8B-7560 | 踏脚板 | 1 | |
| 1P-0820 | 液压拉拔器 | 1 | |
| 9U-6600 | 手动液压泵 | 1 | |
开始:
- 拆下曲轴。 请参阅拆解和组装, "曲轴 - 拆卸"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将曲轴齿轮 (3) 从曲轴 (1) 上拆下。
Show/hide table
 | |
| 图 1 | g00988783 |
- 从曲轴 (1) 上拆下半圆键 (2) 。
安装步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将半圆键 (2) 安置在曲轴 (1) 中。
Show/hide table
| | |
| 图 2 | g00988783 |
Show/hide table
 |
热油和热的部件可能会导致人员受伤。 不要让热的机油和部件接触皮肤。 |
- 加热曲轴齿轮 (3) 。 将曲轴齿轮 (3) 安装在曲轴 (1) 上。
End By: 安装曲轴。 请参阅 拆解和组装, "曲轴 - 安装"。
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
966F Series II Wheel Loader Power Train Transmission Hydraulic Control Valve - Disassemble
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
Supplemental Documentation for the Payload Control System{7494} Supplemental Documentation for the Payload Control System{7494}
953C Track-Type Loader Cooling System Extended Life Coolant Extender - Add
613C Series II Wheel Tractor-Scraper Hydraulic System Elevator Circuit
651E and 657E Wheel Tractor-Scrapers Power train Operational Checks
613C Series II Wheel Tractor-Scraper Hydraulic System Ejector Circuit
953C Track-Type Loader Before Operation
Installation of Direct Conversion Center Tread Idlers {4159} Installation of Direct Conversion Center Tread Idlers {4159}
613C Series II Wheel Tractor-Scraper Hydraulic System Bowl Circuit
2003/03/31 Correction to the Disassembly and Assembly , "Transmission Hydraulic Control Valve - Disassemble" {3073, 3167}
651E and 657E Wheel Tractor-Scrapers Hydraulic System Cylinder Cycle Time - Check
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove
3500B Series II Marine Engines Prelubrication System
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
AD30 Underground Articulated Truck Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
AD30 Underground Articulated Truck Ejector Cylinder Bearing - Lubricate
Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050} Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
2003/03/31 Correction to Disassembly and Assembly , "Axle Shaft Assemblies" {3259}
3508B Engine for Caterpillar Built Machines Air Cleaner
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group
2003/04/07 Special Instruction, REHS1353, "Field Installation of the Engine Speed Control" Is Available {1915}