Pistons and Connecting Rods - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-3601     | 活塞环扩展器     | 1     |
B     | 1P-1861     | 挡圈钳     | 1     |
C     | 5P-8639     | 液压 (连杆轴承)     | 1     |
8F-0024 | 软管组件     | 1     | |
1P-2375 | 快速连接连接器     | 1     | |
1P-2376 | 快速连接连接器     | 1     | |
4C-9751 | 隔套     | 1     | |
4C-9749 | 衬套接头     | 1     | |
4C-9750 | 衬套接头     | 1     | |
9U-6600 | 手动液压泵     | 1     |
注: 从发动机上拆下之前,活塞和连杆组件上已经作了标记。 所有的部件必须重新组装起来。 所有部件必须安装回它们在发动机中原来的位置。 请勿互换任何部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (C) 拆掉旧轴承,同时安装新轴承 (6) 。 工具 (C) 的适配器应与连杆 (3) 的表面充分接触。
注: 将轴承接头两端方位 (X) 正确调整在 12 ± 5 度范围内。
- 沿长度 (Y) 加热连杆 (3) 。
(Y) 加热连杆的最大长度 ... 75 ± 5 mm (3.0 ± 0.2 in)
Show/hide table注意 在安装活塞销子轴承的时候,必须对连杆进行加热处理。 不要使用明火加热。
- 让连杆和轴承冷却到室温。
- 沿长度 (Y) 加热连杆 (3) 。
Show/hide table
图 1 | g01126305 |
Show/hide table
图 2 | g01126306 |
- 用下列程序安装活塞环 (4) 。
- 将控油环的弹簧安置在活塞体组件中的油环槽中。
- 将控油环安置在弹簧的上方。 安置控油环,使其开口与弹簧接头成 180 度。 使用工具 (A) 将控油环安装在活塞上。
- 使用工具 (A) 安装中间活塞环,使有 "UP-2" 标记的一侧朝向活塞顶部。
- 使用工具 (A) 安装顶部活塞环,使有 "UP-1" 标记的一侧朝向活塞顶部。
- 安置活塞环 (4) ,使端隙彼此相隔 120 度。
Show/hide table
图 3 | g01126141 |
- 检查活塞环 (4) 的端隙。 请参阅技术规格, "活塞和活塞环"。
- 将活塞 (1) 放置在连杆 (3) 上。 将清洁的发动机机油涂抹在活塞销 (5) 上,并安装活塞销。 使用工具 (B) 安装挡圈 (2) 。 确保挡圈完全就位在活塞组件的环槽中。
End By: 安装活塞和连杆。 请参阅 拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
966F Series II Wheel Loader Power Train Transmission Hydraulic Control Valve - Disassemble
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
Supplemental Documentation for the Payload Control System{7494} Supplemental Documentation for the Payload Control System{7494}
953C Track-Type Loader Cooling System Extended Life Coolant Extender - Add
613C Series II Wheel Tractor-Scraper Hydraulic System Elevator Circuit
651E and 657E Wheel Tractor-Scrapers Power train Operational Checks
613C Series II Wheel Tractor-Scraper Hydraulic System Ejector Circuit
953C Track-Type Loader Before Operation
Installation of Direct Conversion Center Tread Idlers {4159} Installation of Direct Conversion Center Tread Idlers {4159}
613C Series II Wheel Tractor-Scraper Hydraulic System Bowl Circuit
2003/03/31 Correction to the Disassembly and Assembly , "Transmission Hydraulic Control Valve - Disassemble" {3073, 3167}
613C Series II Wheel Tractor-Scraper Hydraulic System Vane Motor (Elevator)
C7 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
651E and 657E Wheel Tractor-Scrapers Hydraulic System Cylinder Cycle Time - Check
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove
3500B Series II Marine Engines Prelubrication System
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
AD30 Underground Articulated Truck Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
AD30 Underground Articulated Truck Ejector Cylinder Bearing - Lubricate
Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050} Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
2003/03/31 Correction to Disassembly and Assembly , "Axle Shaft Assemblies" {3259}
3508B Engine for Caterpillar Built Machines Air Cleaner
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group