Unit Injector Sleeve - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 372-7975     | 喷油器套筒工具     | 1     |
B     | -     | 测压口 (1/4 - 28 x 15 cm (6 in)) (1)     |
2     |
C     | 8S-4716     | 螺栓 (1/4 - 28)     | 2     |
D     | 1U-7600     | 滑锤拉拔器总成     | 1     |
Show/hide table
( 1 ) | 从 McMaster-Carr 2589A26 采购。 |
开始:
- 拆下单体喷油器。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 有关正确的排放步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 在单体喷油器套管底部定位工具 (A) 。
Show/hide table
图 1 | g03500197 |
- 安装工具 (B) 。 使用工具 (B) 切割进入单体喷油器套管侧的螺纹。 对于另一侧,重复相同的步骤。
Show/hide table
图 2 | g03500360 |
- 安装工具 (C) 。
Show/hide table
图 3 | g03500367 |
- 将工具 (D) 旋入工具 (A) 的顶部。 使用工具 (D) 拆卸单体喷油器套管。
Show/hide table
图 4 | g03500380 |
Caterpillar Information System:
651E and 657E Wheel Tractor-Scrapers Hydraulic System Cylinder Cycle Time - Check
C7 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
966F Series II Wheel Loader Power Train Transmission Hydraulic Control Valve - Disassemble
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
Supplemental Documentation for the Payload Control System{7494} Supplemental Documentation for the Payload Control System{7494}
953C Track-Type Loader Cooling System Extended Life Coolant Extender - Add
613C Series II Wheel Tractor-Scraper Hydraulic System Elevator Circuit
651E and 657E Wheel Tractor-Scrapers Power train Operational Checks
613C Series II Wheel Tractor-Scraper Hydraulic System Ejector Circuit
953C Track-Type Loader Before Operation
Installation of Direct Conversion Center Tread Idlers {4159} Installation of Direct Conversion Center Tread Idlers {4159}
3500B Series II Marine Engines Prelubrication System
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
AD30 Underground Articulated Truck Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
AD30 Underground Articulated Truck Ejector Cylinder Bearing - Lubricate
Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050} Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
2003/03/31 Correction to Disassembly and Assembly , "Axle Shaft Assemblies" {3259}
3508B Engine for Caterpillar Built Machines Air Cleaner
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group
2003/04/07 Special Instruction, REHS1353, "Field Installation of the Engine Speed Control" Is Available {1915}
2003/03/31 Correction to Disassembly and Assembly , "Gear Pump (Axle Oil Cooler) - Remove and Install" {5073}
2003/03/31 Correction to Disassembly and Assembly , "Drive Axle Shafts" {3259}