Electronic Service Tool Will Not Communicate with ECM
- 通信适配器的配置
- 电气接头
- 通信适配器和/或电缆
- 维修工具接头的供电电源
- 电子维修工具及相关硬件
- 电子控制模块(ECM)的供电电源
- 数据链路
起动发动机。 如果发动机无法起动盘车,请参阅故障诊断与排除, "发动机无法起动盘车"。 如果发动机无法起动起来,请参阅故障诊断与排除, "发动机可以起动盘车,但无法起动起来"。 如果发动机起动后,ECM 不能和电子维修工具通信,请继续该程序。
- 访问电子维修工具"实用程序"菜单下的"首选项"。
- 确认选择了正确的 "Communications Interface Device(通信接口设备)"。
- 确认选择了正确的端口供通信适配器使用。
注: 最常用的端口是 "COM 1"。
- 检查有无任何硬件正在使用与通信适配器相同的端口。 如果有任何设备被配置为使用同一端口,请退出或关闭该设备的软件程序。
检查 P1/J1 和 P2/J2 ECM 接头以及诊断接头的安装是否正确。 请参考故障诊断与排除, "电气接头 - 检查"。
- 确保固件和驱动文件是在用通信适配器可以获得的最近文件。 如果固件和驱动文件不匹配,通信适配器将无法与电子维修工具进行通信。
- 将通信适配器和电缆从诊断接头上断开。 将通信适配器重新连接到诊断接头上。
- 确认通信适配器和诊断接头之间使用了正确的电缆。 请参阅故障诊断与排除, "电子维修工具"。
- 如果笔记本电脑使用 Windows 操作系统,请重新启动笔记本电脑,以便消除可能存在的软件冲突。
验证诊断接头的接线端 A 和 B 之间存在蓄电池电压。 如果没有向通信适配器供电,通信适配器的 LED 显示屏将是空白。
为了消除电子维修工具及其相关硬件故障,请将电子维修工具与不同的发动机相连。 如果在不同的发动机上出现相同的故障,请检查电子维修工具和相关硬件,从而确定故障原因。
检查 ECM 的供电。 请参阅系统操作、测试与调整, "充电系统 - 测试"。
注: 如果 ECM 没有接收到蓄电池电压,ECM 将无法通信。
排除数据链路的可能故障。 请参阅故障排除, "数据链路电路 - 测试"。
Caterpillar Information System:
C7.1 (Mech) Industrial Engine Glow Plugs
C-10 Petroleum Engine Piston Cooling Jets - Remove and Install
C15 On-Highway Engine Engine Oil Filter Base
C-10 Petroleum Engine Cylinder Head - Install
C-10 Petroleum Engine Cylinder Head - Remove
2005/07/04 A New High Temperature Gasket is Now Used {1057}
C6.6 Engines for Caterpillar Built Machines Fuel Injection Nozzles
C15 On-Highway Engine Turbocharger
C15 and C18 Engines for Caterpillar Built Machines Piston and Rings
C2.2 Generator Sets Voltage Regulators
C-10 Petroleum Engine Accessory Drive - Install
C9 Engine for Caterpillar Built Machines Pump Drive - Install
C15 On-Highway Engine Cylinder Block
Vane Type Hydraulic Pumps {5055} Vane Type Hydraulic Pumps {5055}
C27 and C32 Engines for Caterpillar Built Machines Fuel Dilution of Engine Oil
345D, 349D and 349D2 Excavator Machine System Specifications Ether Starting Aid
C-10 Petroleum Engine Fuel Pressure Sensor - Remove and Install
C-10 Petroleum Engine Fuel Temperature Sensor - Remove and Install
C-10 Petroleum Engine Turbocharger Outlet Pressure Sensor - Remove and Install
C6.6 Industrial Engine Connecting Rod
12M Motor Grader Cooling System Coolant Sample (Level 2) - Obtain
C-10 Petroleum Engine Inlet Air Temperature Sensor - Remove and Install
C-10 Petroleum Engine Atmospheric Pressure Sensor - Remove and Install
C15 On-Highway Engine Mounting Bracket (Idler Pulley)