Housing (Front) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
B     | 138-7573     | 连杆支架     | 2     |
C     | 1P-0520     | 起子总成     | 1     |
D     | -     | 导向螺柱 (5/8 - 11 x 8 in)     |
2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将密封垫 (11) 安装在缸体上。 在缸体内安装工具 (D) 。
Show/hide table
图 1 | g01131907 |
- 安装工具 (B) ,并将适当起吊设备连接到前驱动器壳体 (2) 上。 前壳体 (2) 的重量约为 181 kg (400 lb)。 将前壳体放置在工具 (D) 上。
- 安装将前壳体 (2) 固定到缸体上的螺栓 (10) 。 拆下工具 (D) ,然后安装其余的螺栓 (10) 。 均匀地拧紧螺栓。
- 从前壳体的底部切除多余的密封垫 (11) 。
- 用工具 (C) 将套筒轴承 (6) 安装到惰齿轮 (5) 中。
Show/hide table
图 2 | g01131955 |
- 在轴 (4) 上安装 O 形密封圈 (8) 。 将干净的发动机油涂抹到用于轴的前壳体 (2) 的孔中。
- 将止推垫圈 (9) 、惰齿轮 (5) 和轴 (4) 定位到前壳体内。 安装螺栓 (7) 。
- 将 O 形密封圈安装到盖 (3) 中。 将护盖 (3) 置于前壳体 (2) 上并安装螺栓。
Show/hide table
图 3 | g01132169 |
- 将衬垫和盖 (1) 安装在前盖上并安装螺栓。
End By:
- 安装辅助水泵。 参考 拆解与组装, "辅助水泵 - 安装"。
- 安装发动机机油泵和水泵驱动器。 参考 拆解和组装, "附件驱动器(前)- 安装"。
- 安装附件驱动器 (前)。 参考 拆解和组装, "附件驱动器(前)- 安装"。
- 安装曲轴前密封和耐磨衬套。 参考 拆解和组装, "曲轴前密封和耐磨衬套 - 安装"。
- 安装发动机机油滤清器底座。 请参阅 拆解和组装, "发动机机油滤清器底座 - 安装"。
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
345C Excavator Leaving the Machine
Replacing the MIDS Display with an Advisor M2 Display{7490} Replacing the MIDS Display with an Advisor M2 Display{7490}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Troubleshooting
2005/03/01 An Improved Exhaust Sleeve Assembly is Now Used on Certain On-Highway Engines {1059, 1100}
2004/12/01 A New PEEC Transducer Module is now Used {1917}
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
3500 Engines Coolant Level Sensor - Remove and Install
325D and 329D Excavators Machine Security System - If Equipped
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Install
2005/01/31 Different Wire Removal Tool and Different Wire Installation Tool Are Required for 85 Pin Connectors on Engine Wiring Harnesses {0709}
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Remove
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install