Housing (Front) - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0074     | 滑锤拉拔器     | 1     |
8B-7557 | 带螺纹的接头     | 1     | |
B     | 138-7573     | 连杆支架     | 2     |
C     | 1P-0520     | 起子总成     | 1     |
D     | -     | 导向螺柱 (5/8 - 11 x 8 in)     |
2     |
开始:
- 拆卸油滤清器座。 请参阅拆解与组装, "发动机机油滤清器底座 - 拆卸"。
- 拆下曲轴前密封和承磨衬套。 参考拆解和组装, "曲轴前密封和耐磨衬套 - 拆卸"。
- 拆卸附件驱动器。 参考拆解与组装, "附件驱动器(前)- 拆卸"。
- 拆卸发动机机油泵和水泵驱动器。 参考拆解与组装, "附件驱动器(前)- 拆卸"。
- 拆卸辅助水泵。 参考拆解与组装, "辅助水泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 卸下螺栓和端盖 (1) 。 从前壳体 (2) 上拆下密封垫。
Show/hide table
图 1 | g01132169 |
- 卸下螺栓和端盖 (3) 。 将 O 形密封圈从盖上拆下。
- 拆下螺栓 (7) 。 使用工具 (A) 从前壳体 (2) 上拆下轴 (4) 。 从轴上拆下 O 形密封圈 (8) 。
Show/hide table
图 2 | g01131889 |
- 将惰齿轮 (5) 和止推垫圈 (9) 从前壳体上拆下。
- 使用工具 (C) 和适当的压具从惰轮 (5) 上拆下套筒轴承 (6) 。
- 安装工具 (B) 并将适当的起吊设备连接到前壳体 (2) 。 前壳体 (2) 的重量约为 181 kg (400 lb)。 拆下两个螺栓,然后安装工具 (D) 。 拆下将前壳体固定到缸体上的剩余螺栓 (10) 。 拆下前壳体。
Show/hide table
图 3 | g01131907 |
- 将密封垫 (11) 从前壳体和缸体上拆下。
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
345C Excavator Leaving the Machine
Replacing the MIDS Display with an Advisor M2 Display{7490} Replacing the MIDS Display with an Advisor M2 Display{7490}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Troubleshooting
2005/03/01 An Improved Exhaust Sleeve Assembly is Now Used on Certain On-Highway Engines {1059, 1100}
C-10, C-12, C-15 and C-16 Industrial Engines Engine Speed/Timing Sensor - Calibrate
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electrical System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Emissions Certification Film
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Plate Locations and Film Locations
C32 Marine Engines Cat Data Link Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Install
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
2004/12/01 A New PEEC Transducer Module is now Used {1917}
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
3500 Engines Coolant Level Sensor - Remove and Install
325D and 329D Excavators Machine Security System - If Equipped
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble