Water Pump - Disassemble
Show/hide table
| Alat yang Diperlukan | |||
| Alat | Nomor Suku Cadang | Keterangan Suku Cadang | Jml |
| A | 5F-7465 | Group Alat Penarik | 1 |
| B | 1P-1861 | Tang Ring Penahan | 1 |
| C | 1P-2320 | Alat Penarik Kombinasi | 1 |
Dimulai dengan:
- Lepaskan pompa air. Rujuk ke Pembongkaran dan Perakitan, "Pompa Air - Pelepasan".
Show/hide table
| PERHATIAN |
|---|
|
Pastikan semua suku cadang bersih dari kontaminan. Kontaminan dapat menyebabkan keausan yang cepat dan mempersingkat umur komponen. |
Show/hide table
| |
| Ilustrasi 1 | g01132114 |
- Lepaskan rakitan elbow (1).
- Lepaskan penutup (3) dari rakitan rumah (7). Lepaskan seal O-ring (2) dan seal O-ring (4).
- Tahan ring hex (14). Lepaskan baut kepala soket (15).
- Lepaskan bearing (13).
- Gunakan Peralatan (C) untuk melepaskan roda gigi (12).
- Gunakan Peralatan (B) untuk melepaskan ring penahan (11). Lepaskan bearing dalam (10).
- Gunakan Peralatan (A) untuk melepaskan impeller (5).
- Gunakan pres yang sesuai untuk melepaskan rakitan poros (9) dari rakitan rumah (7).
- Lepaskan seal air (6).
- Lepaskan seal oli (8).
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
2004/12/01 A New PEEC Transducer Module is now Used {1917}
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
345C Excavator Leaving the Machine
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
3500 Engines Coolant Level Sensor - Remove and Install
325D and 329D Excavators Machine Security System - If Equipped
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Install
2005/01/31 Different Wire Removal Tool and Different Wire Installation Tool Are Required for 85 Pin Connectors on Engine Wiring Harnesses {0709}
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Remove
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install